Contact Us

TPS62402DRCR

Brand: Texas Instruments
Texas Instruments TPS62402DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62402DRCR — Power Management & Signal Chain | Superb Automation

TPS62402DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62402DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62402DRCR: dual step down, 600 mA and 400 mA, fixed 1.8 V and 3.3 V, in a 3 mm VSON body

TPS62402DRCR is a dual synchronous step down converter that produces two fixed rails from one lithium cell or a 5 V bus, with a pin that selects a second voltage on the first rail in a VSON body of 10 pins. It takes 2.5 V to 6 V in and switches at 2.25 MHz, which allows small inductors on both outputs. Rail one is fixed at 1.8 V with 600 mA, and drops to 1.2 V when the DEF_1 pin is pulled low. Rail two is fixed at 3.3 V with 400 mA. Both converters draw 32 uA typical with no load, the shutdown current is 0.1 uA, and the 3 mm by 3 mm body is the smallest of the family.

Order code and package

TPS62402DRCR10 pin VSON (DRC), 3.00 mm by 3.00 mm, 3000 pieces on a large reel, nickel palladium gold finish, moisture level 2 with a one year floor life, marking BYH, minus 40 C to plus 85 C
TPS62402DRCTsame body, 250 pieces on a small reel, the pilot quantity
TPS62400DRCRthe adjustable member, both rails set by external dividers from a 0.6 V reference, 3000 pieces on a large reel
TPS62401 and TPS62404fixed members with different factory voltages, 1.1 V and 1.575 V on rail one in the 01, and 1.9 V and 1.2 V on rail one in the 04
TPS62403fixed 1.1 V and 1.575 V on rail one with 2.8 V on rail two, the member that suits a 2.8 V logic rail
Reel columnthe addendum rows for this family print the quantity one row above the part number, so the packing has to be read from the R or T suffix rather than from the row it appears on

Electrical parameters that decide the application

Input voltage2.5 V to 6 V operating, and the lockout releases between 1.5 V and 2.35 V when the input falls
Output one1.8 V fixed with the DEF_1 pin high and 1.2 V with it low, 600 mA maximum
Output two3.3 V fixed, 400 mA maximum, with no pin selection on this member
Switching frequency2.0 MHz to 2.5 MHz with a 2.25 MHz typical, fixed, and the two converters run 180 degrees out of phase to halve the input ripple
Quiescent current32 uA typical for both converters running with no load, and 0.1 uA typical in shutdown
Reference0.6 V typical on the adjustable member, and an internal divider on the fixed members that keeps the accuracy at 1 per cent in pulse width modulation mode
Switch resistance280 milliohm typical and 620 milliohm maximum on the high side, 200 milliohm and 450 milliohm on the low side, both at 3.6 V
Duty cycle100 per cent, which lets the converter follow a falling input down to the output plus the resistive drop instead of dropping out
Mode pinthe MODE/DATA pin doubles as the EasyScale data line, and pulling it high forces fixed frequency operation for low noise
Output capacitors10 uF ceramic on each rail in the vendor application circuit, with a 2.2 uH inductor on rail one and a 2.2 uH on rail two
Protectioncurrent limit in both the high side and the low side switch, thermal shutdown, and a soft start ramp on each converter

How the fixed members differ

TPS62401rail one 1.1 V or 1.575 V, rail two 1.8 V, 600 mA on rail one and 400 mA on rail two
TPS62402rail one 1.8 V or 1.2 V, rail two 3.3 V, the combination that feeds a processor core and its input output ring from one part
TPS62403rail one 1.1 V or 1.575 V, rail two 2.8 V, for a 2.8 V analogue rail
TPS62404rail one 1.9 V or 1.2 V, rail two 3.3 V
TPS62400both rails adjustable from 0.6 V to the input, which is the only member that can build a rail below 1.1 V or above 3.3 V
EasyScale interfaceone pin, present on all five members, that can change the rail one voltage during operation for dynamic scaling without a second wire

Points to check before this part goes on a BOM

The DEF_1 pin is a digital input on the fixed members, not an analogue one. Pulling it high gives 1.8 V on rail one, pulling it low gives 1.2 V, and the switch happens while the converter is running. That is the whole dynamic scaling feature on this member, and it comes with a caveat: the change is a step, not a ramp, so a load that cannot tolerate a 600 mV step has to take the EasyScale route on the MODE/DATA pin instead, which changes the voltage in smaller increments.

Rail two is fixed at 3.3 V and cannot be moved on this member. A board that needs 2.8 V on the second rail moves to TPS62403, and a board that needs two adjustable rails moves to TPS62400. The five members share a body, a pinout and a reel, and they differ only in the factory programmed divider, which means the order code is the only thing that distinguishes them on a purchase order and a wrong suffix produces a working board with the wrong rail voltage.

The 32 uA quiescent current is quoted for both converters running with no load, which is the state that matters for a product that stays on. The shutdown row is 0.1 uA typical and 1 uA maximum, and that is what the battery sees when the enable pins are low. Neither figure includes the leakage of the output capacitors or of the load, so a standby budget built only from this datasheet will be optimistic in a real assembly.

The 180 degree phase relationship between the two converters is a real feature of the part rather than a detail. With both switching at 2.25 MHz and out of phase, the input capacitor sees a ripple at 4.5 MHz in the ideal case, which halves the capacitance needed and moves the ripple out of the band a radio front end cares about. A board that disables one converter loses that benefit, and a board that runs them at different frequencies cannot, because the frequency is fixed internally.

The 100 per cent duty cycle mode is what makes this family usable from a single cell. As the battery falls toward 3.3 V, rail two follows the input down instead of dropping out at the point where the duty cycle would otherwise reach its limit, so a 3.3 V load keeps working on a 3.4 V battery with only the resistive drop across the high side switch. The output is then not regulated, it is the input minus the drop, and any load that needs a true 3.3 V at that point needs a buck boost instead.

The moisture level on the DRC body is 2 with a one year floor life, which is normal for a 3 mm by 3 mm VSON and worth writing on the process sheet. An opened reel that sits on the floor for more than a year needs a bake before reflow. The same body appears across all five members, so a change from one voltage option to another does not change the floor life or the reflow profile.

The current limit is implemented on both switches rather than on the output. When the high side reaches its limit it turns off and the low side takes over, and the high side only returns once the current in the low side falls below its own limit. That behaviour matters during a short circuit, because the converter does not latch off. It folds back and keeps switching at a low duty cycle, which keeps the die cooler than a hard limit would and also means the fault current is not zero.

Where this order code fits

It sits in handheld instruments, portable media players and processor boards that need a core rail and an input output rail from one battery, where two converters in one 3 mm body save the space a second inductor would take. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

What voltages does this member produce? Rail one 1.8 V with the DEF_1 pin high and 1.2 V with it low at 600 mA. Rail two 3.3 V fixed at 400 mA.

Can rail two be changed to 2.8 V? Not on this member. TPS62403 is the member with a 2.8 V second rail on the same body and pinout.

What is the quiescent current with both rails on? 32 uA typical with no load, and 0.1 uA typical in shutdown with the enable pins low.

Does it work from a single lithium cell? Yes from 2.5 V to 6 V. Below 3.3 V the 3.3 V rail follows the input down through the 100 per cent duty cycle mode rather than dropping out.

How is the reel size identified? By the suffix: R is 3000 pieces on a large reel and T is 250 on a small reel. The addendum table prints the quantity one row above the part number in this family.

What does the MODE/DATA pin do? It forces fixed frequency operation when pulled high, and it carries the one pin EasyScale data when the rail voltage has to be changed during operation.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Kitting Service page sets out the checks that keep a substitute from failing on the bench.