Contact Us

TPS75733KTTR

Brand: Texas Instruments
Texas Instruments TPS75733KTTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS75733KTTR — Power Management & Signal Chain | Superb Automation

TPS75733KTTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS75733KTTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS75733KTTR: 3 A fixed 3.3 V regulator with 150 mV of dropout in a TO-263

TPS75733KTTR is a 3 A low dropout regulator in the five pin KTT body with a fixed 3.3 V output, 150 mV of dropout at full current, 125 uA of quiescent current and an open drain power good output in a TO-263 body of 5 pins. The TPS75733 is the 3.3 V member of the TPS757 family, which provides 1.5 V, 1.8 V, 2.5 V and 3.3 V fixed outputs plus an adjustable version, all at 3 A. The dropout is 150 mV typical at 3 A, the quiescent current is 125 uA, and the fixed versions carry an open drain power good output that goes low when the output falls to about 91 percent of its nominal value. Accuracy is 3 percent over the specified conditions for the fixed versions, and the package is a five pin TO-263.

Order code and package

Order codeTPS75733KTTR
Output voltage3.3 V fixed
Output current3 A
Dropout at 3 A150 mV typical
Quiescent current125 uA typical
Accuracy3 percent over the specified conditions
Power goodopen drain, on the fixed versions
Packagefive pin TO-263, KTT body

Electrical parameters that decide the application

Fixed output options1.5 V, 1.8 V, 2.5 V, 3.3 V and adjustable
Power good trip pointtypically 91 percent of the output voltage
Power good hysteresisthe difference between the falling and rising trip points
Alternate packagefive pin TO-220
Dropout at lower currentsproportional to the current, not a fixed value
Output capacitorrequired for stability, value given in the application section
Thermal paththrough the tab to the copper

Points to check before this part goes on a BOM

A hundred and fifty millivolts at 3 A is 0.45 W in the pass device, and the same regulator dropping 5 V to 3.3 V at 3 A dissipates 5.1 W regardless of its dropout. The dropout figure describes the minimum headroom, not the operating dissipation, and the two numbers are confused often enough to be worth separating: a 5 V to 3.3 V stage has 1.7 V across the device and the dissipation is set by that, while a 3.45 V to 3.3 V stage has 150 mV and the dissipation is a tenth of it. Only the second case benefits from a low dropout part.

Three percent accuracy on a fixed output is a wider window than a modern regulator and it is a consequence of the fixed resistor network inside the package. On a 3.3 V rail that is 99 mV, so a load rated at 3.135 V minimum has 165 mV of margin against the regulator's own low limit. That is enough for most digital loads and not enough for a load with a 1 percent requirement, which is where an adjustable part with external precision resistors becomes the only option.

The power good trip at 91 percent of the output is a flag that asserts before the rail is out of regulation, which is the right behaviour for holding a processor in reset. At 3.3 V the flag falls at 3.0 V, so a processor rated to 3.0 V is released just as it reaches its own limit. A board that needs more margin either uses a separate supervisor with a higher threshold or accepts that the flag is an indication rather than a guarantee.

A hundred and twenty five microamps of quiescent current is low for a 3 A regulator and it is the current that flows when the load is zero. The number matters for a product that leaves the rail alive in standby: 125 uA over a year is 1.1 Ah, which on a 10 Ah battery is a tenth of the capacity. That is a large number for a mains powered product and a significant one for a battery product, and the alternative is to switch the rail rather than leave it regulated.

A five pin TO-263 carries 3 A through a tab that is also the ground connection for some variants, so the thermal path and the return path are the same piece of copper. That is convenient and it means the tab has to be soldered to a plane that is both the heatsink and the reference for the output capacitor, which is why the application section places the output capacitor close to the tab rather than close to the output pin. A capacitor placed at the wrong end of the tab connection sees the load current in its ground path.

The dropout is specified at 3 A and it scales with current, so a board that runs at 1 A has about 50 mV of dropout rather than 150 mV. The scaling is not exactly linear because the pass device is a MOS transistor in its linear region, but the direction is what matters: a regulator used at a third of its rating has a third of the dropout, which is the reason a 3 A part is sometimes chosen for a 1 A load when the headroom is tight.

The family includes 1.5 V, 1.8 V, 2.5 V and 3.3 V versions in the same body with the same pinout, so a board can be built for one rail and reworked for another without a board change. That flexibility is useful in a product family and it is also a trap: the parts are not interchangeable electrically, and a board stuffed with the 1.8 V version in place of the 3.3 V version powers up, regulates, and destroys the load with no visible symptom until the load fails.

Where this order code fits

This order code belongs on post regulation of a 5 V rail in industrial equipment, on local regulation for a card that receives a loosely specified backplane voltage, and on any 3 A load that needs a quiet rail without a switching converter. It is also the part chosen where a power good signal is needed to hold a processor in reset until the rail is valid, because the flag is on the package and does not need an external comparator. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

When is a low dropout part actually needed? When the input is close to the output. A 5 V to 3.3 V stage dissipates 5.1 W at 3 A regardless of the dropout, so a low dropout device buys nothing. A 3.45 V to 3.3 V stage dissipates 0.45 W, and there the 150 mV figure is the whole reason the board works.

What does the power good output signal? It goes low when the output falls to about 91 percent of nominal, which on a 3.3 V rail is 3.0 V. It is an indication that the rail is close to the load's minimum, not a guarantee that the load is in specification, so a product that needs a guarantee uses a separate supervisor.

Can the 1.8 V version be used on a 3.3 V board? No. The pinout and the package are the same, so the part fits and regulates at its own voltage, which means the board runs a 3.3 V load at 1.8 V. The failure is silent until the load stops working, which is why the reel label and the marking are the checks that matter in a mixed production area.

How much headroom does it need at 1 A? The dropout scales with current, so at 1 A it is roughly 50 mV rather than 150 mV. A board with 200 mV of headroom at 1 A is comfortable, and the same board at 3 A is at the limit of the specification.

SUPERB holds and sources this regulator line against the exact order code, with the reel, date code and country of origin stated on the offer. When a rail has to move to a second part, the Component Lead Time Solutions page sets out the checks that separate a working substitute from one that fails on the bench.