TPS74401KTWR
Product Specifications
TPS74401KTWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS74401KTWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS74401KTWR: 3 A linear regulator with 115 mV of dropout and a programmable soft start
TPS74401KTWR is an ultra low dropout regulator in the seven pin KTW body that delivers 3 A with 115 mV of dropout, takes its input from 1.1 V to 5.5 V, sets its output anywhere from 0.8 V to 3.6 V and controls its turn on ramp with a single capacitor in a TO-263-7 body of 7 pins. The TPS74401 is a 3 A linear regulator with a bias pin that allows the input to sit close to the output while keeping the internal circuitry supplied from a higher rail. Input range is 1.1 V to 5.5 V, output is adjustable from 0.8 V to 3.6 V with 1 percent accuracy over line, load and temperature, and the dropout at 3 A is 115 mV on the legacy die and 120 mV on the current die. A capacitor on the soft start pin sets the ramp, and an open pin gives about 100 us, while a power good output allows the rail to be sequenced against others.
Order code and package
| Order code | TPS74401KTWR |
| Output current | 3 A |
| Input voltage | 1.1 V to 5.5 V |
| Output voltage | 0.8 V to 3.6 V, adjustable |
| Dropout at 3 A | 115 mV typical on the legacy die, 120 mV on the current die |
| Accuracy | plus or minus 1 percent over line, load and temperature |
| Soft start | capacitor programmable, 100 us with the pin open |
| Package | seven pin TO-263, KTW body |
Electrical parameters that decide the application
| Bias pin | allows low input operation with good transient response |
| Bias to output headroom for full specification | 1.62 V |
| Output capacitor, current die | any type of 2.2 uF or larger |
| Output capacitor, legacy die | stable with any capacitor or none |
| Input capacitor | 1 uF or larger recommended |
| Bias capacitor | 1 uF or larger recommended, 4.7 uF when the bias pin is tied to the input |
| Power good | open drain, needs a pull up between 10 kohm and 1 Mohm |
| Load regulation | 0.09 percent per amp |
| Alternate package | 20 pin VQFN |
Points to check before this part goes on a BOM
A hundred and fifteen millivolts of dropout at 3 A is 0.345 W in the pass device, which is the number that makes this part usable after a switching converter. A conventional regulator with 500 mV of dropout would dissipate 1.5 W at the same current and need a heatsink, which is the difference between a post regulator that fits on a card and one that does not. The catch is that the input has to be within 115 mV of the output, so the upstream converter has to be set precisely, and a 3.3 V rail feeding a 3.0 V output has 300 mV of headroom, which is more than enough and leaves 185 mV of margin for tolerance.
The bias pin is what makes the low input possible, and the 1.62 V of headroom to the output is the condition for the full specification. The internal circuitry is supplied from the bias rail, so the pass device can operate with its input only slightly above the output. A board that ties the bias pin to the input loses that advantage: the bias is then at the input voltage, which must be at least 1.62 V above the output, and the low dropout capability is gone. The two connections look similar on a diagram and behave completely differently.
One percent accuracy over line, load and temperature is unusual for a 3 A regulator and it is what allows the part to be used as a reference for a converter. The load regulation of 0.09 percent per amp is 0.27 percent at full current, which is inside the 1 percent but is the largest single term in it. A rail that has to hold 1 percent across a load step from zero to 3 A therefore uses almost a third of its budget on load regulation alone, before the reference and the divider are counted.
The soft start capacitor is the answer to a card that trips a backplane supply. Charging 100 uF to 1.2 V in 100 us draws 1.2 A, which is inside the 3 A rating but is a step load on the upstream converter. The same capacitance charged in 10 ms draws 12 mA, so the capacitor turns an inrush into a controlled ramp and moves the problem from the power supply to a component. An open soft start pin gives 100 us, which is the fastest the part will go, so a board that needs a slower ramp adds capacitance rather than relying on the default.
Power good is an open drain output that needs a pull up between 10 kohm and 1 Mohm, and the value matters for the rise time of the signal. A 1 Mohm pull up into 50 pF of board capacitance has a 50 us time constant, which is slower than the ramp of the rail it is reporting. A sequencer that uses power good as a trigger therefore starts the next rail late by an amount that depends on the pull up, and that delay is not in any specification because it is a property of the board.
Two die versions exist under the same order code, the legacy die and the current die, and they differ in the output capacitor requirement. The legacy die is stable with any output capacitor or none, and the current die needs 2.2 uF or more. That is a real difference for a board that was built for the legacy part with no output capacitor at all: the same order code can arrive with a die that oscillates. A board with no output capacitor should be checked against the marking or against the date code rather than assumed.
Seven pins in a TO-263 package carry 3 A, and the dissipation is what the tab is for. At 3 A and 115 mV the loss is 0.345 W, which the package handles on a modest copper area. The loss rises as the square of the current, so a board that runs at 3 A continuously and 4 A in a transient is dissipating 0.9 W in the transient, and the thermal time constant of the tab is what decides whether that reaches the junction. A TO-263 is a package with a large thermal mass, which is why it survives short overloads that a small QFN would not.
Where this order code fits
This order code belongs on post regulation of switching rails in test equipment, medical instruments, communications cards and data acquisition, where the switching noise of the upstream converter has to be removed without dropping the headroom. It is also the part chosen where a rail has to come up slowly, because the soft start capacitor sets the ramp independently of the load and the inrush into a large decoupling network is what limits a card's power up current. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
What does the bias pin do? It supplies the internal circuitry from a rail higher than the input, so the pass device can work with only 115 mV across it. Without the bias, the input has to be at least 1.62 V above the output for the full specification, and the low dropout advantage disappears.
Can it follow a switching converter closely? Yes, that is its purpose. A 3.3 V switching rail post regulated to 3.0 V has 300 mV of headroom, so the regulator runs with 185 mV of margin above its 115 mV dropout and removes the switching ripple. The upstream converter has to be accurate enough that its low limit stays above the regulator's dropout.
How is the turn on ramp set? By a capacitor on the soft start pin. An open pin gives about 100 us, and larger capacitors extend the ramp. The ramp current is fixed internally, so the time is proportional to the capacitance, and the inrush into the load capacitance is the load current divided by the ramp time.
Which output capacitor does it need? The current die needs any type of 2.2 uF or larger. The legacy die is stable with any capacitor or none. Both are supplied under the same order code, so a board built with no output capacitor has to be checked against the die it receives rather than against the datasheet it was written from.
SUPERB holds and sources this regulator line against the exact order code, with the reel, date code and country of origin stated on the offer. When a rail has to move to a second part, the Component Lead Time Solutions page sets out the checks that separate a working substitute from one that fails on the bench.