TPS62122DRVR
Product Specifications
TPS62122DRVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62122DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62122DRVR: 15 V input, 75 mA buck converter for energy harvesting and low power radio nodes
TPS62122DRVR is a 75 mA synchronous step down converter with a hysteretic loop, an 11 uA quiescent current and a 2 V to 15 V input range in a SON body of 6 pins. The output is set from 1.2 V to 5.5 V against a 0.8 V reference, and the converter reaches up to 96 per cent efficiency at 800 kHz switching. It keeps 100 per cent duty cycle for the lowest dropout, starts from 2.5 V typically, and runs down to a 1.85 V falling lockout so a pair of cells can be used to the end.
Order code and package
| TPS62122DRVR | 6-pin SON (DRV), 2.00 mm by 2.00 mm, large reel |
| TPS62120DCNR | 8-pin SOT-23, adds a power good output and an output discharge pin |
| Output current | 75 mA |
| Output voltage range | 1.2 V to 5.5 V |
| Operating junction temperature | -40 C to 85 C |
Electrical parameters that decide the application
| Input voltage range | 2 V to 15 V, 2.5 V typical for start up |
| Output current | 75 mA, falling at low input voltage |
| Output current at 2 V in and 1.8 V out | 25 mA with a 0.7 Ohm inductor |
| Feedback reference | 0.8 V |
| Quiescent current, power save mode | 11 uA typical, 18 uA maximum |
| Switching frequency | up to 800 kHz, load dependent in power save mode |
| Undervoltage lockout | 2.5 V rising, 1.85 V falling |
| Duty cycle | 100 per cent, so the dropout is the resistance of the switch and inductor |
| Efficiency | up to 96 per cent |
Where the two members of the family differ
| TPS62122 | 6-pin SON, no power good output, no output discharge pin, the row on this page |
| TPS62120 | 8-pin SOT-23, adds a power good output at 95 per cent rising and 90 per cent falling |
| TPS62120 discharge pin | pulls the output down while the part is in shutdown |
| Power save mode | pulse frequency modulation at light load, pulse width modulation at heavy load |
| Hysteretic loop | no external compensation, the output capacitor and inductor set the behaviour |
| No external rectifier | the synchronous switch replaces the diode, which is where the efficiency comes from |
Points to check before this part goes on a BOM
The 75 mA rating is a headline and it is not available at 2 V in. The document quotes 25 mA into 1.8 V from a 2 V input with a 0.7 Ohm inductor, because at that ratio the switch resistance and the inductor resistance are a large part of the available headroom. A product running from two alkaline cells near end of life has to be sized for the current at 2 V, not for the number on the front page.
The falling lockout at 1.85 V is what makes a two cell product usable to the end of the cells. The part starts at 2.5 V, and once running it continues until the input falls below 1.85 V. A single cell lithium product cannot use that window, but a two cell alkaline product can, and the difference between 2.5 V and 1.85 V is most of the last hour of runtime.
The 100 per cent duty cycle mode is the reason the part can work as a pass element when the input falls close to the output. In that mode the switch stays on and the output is the input minus the resistive drop, so a 1.8 V rail from a 2 V input is possible at low current. There is no boost, so once the input falls below the output the rail follows it down.
The quiescent current is 11 uA typical and 18 uA maximum in power save mode. On a node that sleeps for minutes and wakes for milliseconds, that figure sets the battery life, and the 18 uA maximum matters more than the typical, because the maximum is what a cold morning and an aged cell will produce. A node that budgets on the typical number will fall short in the field.
The hysteretic loop has no compensation, and the trade is ripple against transient response. The loop reacts on every cycle to the feedback voltage crossing, so the output ripple is set by the hysteresis and the output capacitor, and the response to a load step is immediate. A product that needs a quiet rail adds output capacitance rather than changing a component value.
The switching frequency is not fixed, it falls with load in power save mode. That is good for efficiency and awkward for anything that scans for emission at a fixed frequency. A radio node that shares a board with this converter can see the switching energy move as the load changes, and a filter chosen for the worst case 800 kHz does not cover the low frequency end of the range.
The 2 mm by 2 mm six pin body has no exposed pad on some rows and the ground pin carries the heat. At 75 mA and a few volts the dissipation is small enough that this is not the limit, but at 15 V in and 1.2 V out at 50 mA the part dissipates 0.69 W, and a six pin body with no pad cannot hold that. The input voltage and the output voltage together decide whether the part is inside its thermal envelope.
The 0.8 V reference allows an output below 1.2 V in principle, and the quoted range starts at 1.2 V because that is where the loop and the minimum on time remain well behaved. A rail at 1.0 V from this part is possible on paper and outside the specified range, so a product that needs 1.0 V is looking at a different part rather than a different divider.
An inductor of 0.7 Ohm is quoted in the current capability row, and that number is part of the specification rather than a suggestion. A lower resistance inductor gives more output current at low input and a physically larger part, and a higher resistance part removes current capability without any warning other than a rail that will not start under load.
The output capacitor carries the full load current during the off time, because the loop is hysteretic and the inductor ripple is large. A ceramic capacitor is required rather than a tantalum, and the capacitance at the operating voltage is the number that matters. At 5 V out with a 6.3 V rated ceramic the derating is severe and the ripple grows accordingly.
The family split matters at the bill of materials level. The SOT-23 member adds a power good output and an output discharge pin, the SON member does not. A board laid out for the SOT-23 part cannot take the SON part without a footprint change, and a substitute during a shortage that only checks the electrical ratings will produce a board with an unconnected pin.
The part is a step down converter with no boost capability, so a two cell product whose rail is 3.3 V stops regulating once the cells fall below about 3.4 V. For a product that has to run to 1.85 V, the rail has to be lower than that, which is why the family is used at 1.8 V rather than at 3.3 V. The choice of rail voltage is really a choice about how much of the cell curve is usable.
Where this order code fits
It sits between a pair of cells or a harvested source and the radio or sensor on a wireless node, where the average current is microamps and the standby consumption of the converter decides the battery life. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
How much current can it deliver from two alkaline cells? At 2 V in and 1.8 V out the document quotes 25 mA with a 0.7 Ohm inductor, and the 75 mA rating applies with more headroom. The number to use for a battery product is the current at the lowest input voltage the product allows.
Does it need an external diode? No. The converter is synchronous and the low side switch replaces the rectifier, which is where part of the efficiency comes from. The loop is hysteretic and needs no external compensation.
What happens below 1.85 V? The part locks out and the output turns off. Above that, and below the 2.5 V start up threshold, a running part keeps regulating, which is the window that lets two cells be used down to the end of their curve.
Can the output be 3.3 V? Yes, the range goes to 5.5 V, and the input has to stay above the output by the dropout of the switch and inductor. With 100 per cent duty cycle the part behaves as a pass element when the input is close to the output.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.