Contact Us

TPS73601DRBRM3

Brand: Texas Instruments
Texas Instruments TPS73601DRBRM3 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS73601DRBRM3 — Power Management & Signal Chain | Superb Automation

TPS73601DRBRM3

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS73601DRBRM3 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS73601DRBRM3 adjustable 400 mA regulator, third silicon revision

The TPS73601DRBRM3 is the adjustable member of the TPS736 family in the eight pin three millimetre SON, on the M3 revision of the silicon, a 400 mA regulator that runs from 1.7 V to 5.5 V and needs no output capacitor at all. The family topology is an NMOS pass device in a follower configuration, which is what allows the capacitor free operation, and it is also what gives the part a ground current that stays flat across the load range instead of climbing at full current.

The M3 suffix is the item to read twice. The plain row and the M3 row of this string carry different reel data and different lead finish columns in the addendum, and the M3 row prints Call TI in both the finish and the moisture level columns while other rows of the same family print a specified tin finish at level 2. That is not a defect in the part, it is the vendor not having published the packaging data for that revision, and a line that needs a floor life documented before receipt will not find it here.

Key parameters from the SBVS038X document

Input range1.7 V to 5.5 V, minimum also limited by output plus dropout
OutputAdjustable 1.2 V to 5.5 V on a 1.204 V reference, window 1.198 V to 1.210 V
Current400 mA continuous, foldback current limit
Accuracy0.5 percent typical, 1 percent maximum over load, line and temperature
Dropout75 mV typical, 200 mV maximum at 400 mA
Output capacitorNone required, stable with any value or type, 30 microvolt RMS noise with a 0.1 microfarad noise reduction capacitor
Ground current400 microamp typical, 550 microamp maximum on the legacy chip and 630 on the current chip
Current limit400 to 650 mA on the legacy chip, 500 to 800 mA on the current chip, 450 mA at a shorted output
Reverse currentBlocked, 0.1 microamp typical and 10 microamp maximum with the enable low
Shutdown current0.02 microamp typical, 1 microamp maximum
PackageDRB eight pin SON, 3 mm by 3 mm, marking PJFQ
Order codeTPS73601DRBRM3 active at 3000 pieces on a large reel, the .A row of the same string is the 250 piece small reel

Why the reverse current specification matters here

A follower pass device blocks current from the output back to the input by construction, and the document quantifies it at 0.1 microamp typical with a 10 microamp maximum. On a board with several rails, one of which can come up before the input of this regulator, that property prevents the charged rail from discharging through the regulator into an unpowered bus. Without it the rail sags, and in the worst case the upstream converter sees a reverse current that it was not built to handle.

The same topology is why the part is stable with no capacitor and why its transient response with a capacitor is not much better than without one. A 0.1 microfarad capacitor is still worth fitting where the load steps quickly, and the 30 microvolt noise figure is quoted with that capacitor on the noise reduction pin, not on the output.

Where this part fits

Portable instruments, radio front ends, sensor boards and any board where one rail can be alive before another use this family for the reverse blocking. Our notes for boards that need a quiet low current rail next to a switching converter are under RF component sourcing, and the way we handle a revision change inside one order code is in supplier corrective action.

What to check before a purchase order

Check which silicon revision is in the box. The two chips differ in ground current maximum (550 against 630 microamp), in current limit window (400 to 650 against 500 to 800 mA) and in the input transient behaviour, while the order code and the marking on an eight pin SON are not enough to tell them apart at receipt. A production lot built on one revision and replenished with the other will show a different inrush signature on the same board.

Check the divider values against the 1.204 V reference. The reference window is plus or minus 0.5 percent, so the 1 percent overall accuracy figure is mostly the divider and the load regulation. Using 1 percent resistors is the cheapest way to keep the rail inside 1 percent, and 5 percent parts will not.

Questions that come up on this part

What does the M3 suffix change? The vendor lists it as a separate orderable row at the same body and reel size, and the electrical table gives different rows for the legacy and current chips. The conservative reading is that M3 identifies the current silicon, and the packaging data for that row is still marked Call TI.

Is a feed forward capacitor needed? For the adjustable member it improves the transient response and the rejection at high frequency, and the document shows the values. It is not needed for stability, which is the point of this family.