Contact Us

TPS745135PQWDRBRQ1

Brand: Texas Instruments
Texas Instruments TPS745135PQWDRBRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS745135PQWDRBRQ1 — Power Management & Signal Chain | Superb Automation

TPS745135PQWDRBRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS745135PQWDRBRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS745135PQWDRBRQ1 1.35 V automotive regulator with power good

The TPS745135PQWDRBRQ1 is the fixed 1.35 V member of the TPS745-Q1 family, a 500 mA low dropout regulator in the eight pin VSON body that measures 3 mm by 3 mm with wettable flanks, on a 3000 piece reel. The code decodes through the vendor nomenclature: 135 is the output at 1.35 V in three digits because the step is not a round hundred millivolts, P is the active output discharge that every member of the family has, the absent letter after P means an open drain power good output with a 150 microsecond delay, Q is the AEC-Q100 grade 1 marking, W is the wettable flank body, and the final Q1 confirms the automotive grade.

The 1.35 V point is not a common logic rail. It appears on camera modules, on DDR memory rails and on processor cores that sit just above the 1.2 V point for margin. The family covers 0.65 V to 5.0 V in 50 mV increments on the fixed side, so 1.35 V is one of the standard steps rather than a custom trim.

Key parameters from the SBVS355C document

Input range1.5 V to 6.0 V
Output1.35 V fixed, the family covers 0.65 V to 5.0 V in 50 mV steps and 0.55 V to 5.5 V adjustable
Current500 mA continuous, current limit window 515 to 865 mA with 720 mA typical
Short circuit current200 to 400 mA with 350 mA typical, foldback so the part does not sit at the full limit into a short
AccuracyPlus or minus 0.85 percent at 25 degrees and plus or minus 1.5 percent maximum over temperature
Dropout285 mV typical and 430 mV maximum at 500 mA in the 1.2 to 1.5 V output band
Quiescent current25 microamp typical, 1.5 microamp in shutdown, 0.1 microamp of feedback pin current
Rejection45 dB at 100 kHz, which is the figure that matters behind a switching supply
Output capacitorStable with 1 microfarad ceramic or larger
Thermal resistance55.5 degrees per watt junction to ambient in the eight pin VSON body, 80.3 in the six pin WSON
QualificationAEC-Q100 grade 1, minus 40 to 125 degrees ambient, junction rated to 150 degrees
Order codeTPS745135PQWDRBRQ1, VSON eight pin wettable flank, 3000 pieces on a large reel, level 2, one year floor life

Dropout is quoted by output band, not as one number

The document prints the dropout row in bands because the pass device has to hold a fixed fraction of the output, and a 1.35 V rail is a tighter case than a 3.3 V rail. In the 1.2 V to 1.5 V band the figure is 285 mV typical and 430 mV maximum at 500 mA. In the 1.5 V to 1.8 V band it falls to 180 mV typical and 265 mV maximum, and at 3.3 V out the maximum is 160 mV. A customer who quotes the 160 mV figure for a 1.35 V rail is using the wrong row, and the error is nearly 300 mV of headroom.

That matters on an automotive rail because the input is a battery line that sags during a cold crank. A 1.35 V rail fed from a 3.3 V buck has plenty of margin. The same rail fed directly from a 2.5 V supply in a brown out has 1.15 V of margin against the 430 mV maximum, which holds, while a rail budget that assumed 160 mV of dropout and 500 mV of sag does not.

What the package letters tell a buyer

The P in the string is the active output discharge, and the vendor states that every member of the family has it, so the letter is present on all rows and does not indicate a special order. The letter that is missing is the one that matters: the nomenclature defines a blank position as an open drain power good with a 150 microsecond delay, B as open drain with a 5 millisecond delay, and C as push pull with a 150 microsecond delay. The catalogue entry carries no letter, so this part has the fast open drain output, and a board that needs the 5 ms delay to debounce a slow rail has to order the B variant instead.

The W is the wettable flank body, which is there for optical inspection of the solder joint on an automotive line. A customer who does not run automated optical inspection still gets the same die in the same footprint, and the flank costs nothing in electrical terms.

Where this part fits

Automotive head units, front and rear cameras, cluster displays, telematics control units and short range radar are the applications in the document, which maps onto the camera and sensor rails we quote most often. Our notes on the automotive qualification route sit under power management cross reference, and the date code and traceability rules we apply to automotive reels are in date code management.

Before a purchase order, and the questions that come up

The thermal case is easy at 500 mA and still has to be checked. Dropping 3.3 V to 1.35 V at 500 mA burns 0.98 W, which with a 55.5 degree per watt body is a 54 degree rise and a junction near 149 degrees at a 95 degree ambient, just at the limit. At 250 mA the same rail burns 0.49 W and the margin comes back. Cameras run at a few hundred milliamps, so the part is normally comfortable, and the numbers should still be run for each rail.

Does the part need a feed forward capacitor? The document discusses it in the application section for transient response, and the fixed member has an internal divider, so the capacitor goes across the upper divider resistor only on the adjustable member. On this fixed part there is nothing to bypass.

What happens during a cold crank? The input can fall below the 1.5 V minimum, and the undervoltage lockout holds the output off rather than letting it follow the input down. The power good output goes low at the same time, which is the signal a downstream processor should use to hold in reset.

Is the reel size the same across the family? Both bodies print 3000 pieces, so no. The difference between the six pin and the eight pin body is the thermal resistance and the footprint, not the packing.