Contact Us

TPS74201RGRR

Brand: Texas Instruments
Texas Instruments TPS74201RGRR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS74201RGRR — Power Management & Signal Chain | Superb Automation

TPS74201RGRR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS74201RGRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS74201RGRR 1.5 A regulator with programmable soft start

The TPS74201RGRR is the adjustable member of the TPS742 family in the twenty pin VQFN body that measures 3.5 mm by 3.5 mm, on a 500 piece reel. It is a 1.5 A low dropout regulator that runs a main input from 0.8 V to 5.5 V with a bias supply, sets its output from 0.8 V to 3.6 V from a 0.8 V reference, and adds two features that the smaller regulators do not have: a soft start pin whose ramp time is set by an external capacitor, and an open drain power good output for sequencing.

The soft start is the reason to pick this part on a board with several rails. The pin charges an external capacitor with a fixed current, and the output follows that ramp, so the inrush into the load capacitance is controlled by the capacitor value rather than by the regulator's own turn on behaviour. On a board where four rails come up in sequence and the first one has to be stable before the second is allowed to start, that ramp and the power good output together do the job without an external sequencer.

Key parameters from the SBVS064P document

Main input0.8 V to 5.5 V, with the floor set by output plus dropout
Bias input2.375 V to 5.25 V, which is what allows the main input to sit below 2 V
Output range0.8 V to 3.6 V adjustable from a 0.8 V reference
Current1.5 A continuous, current limit allows surges of 1.8 A while regulation is held
AccuracyPlus or minus 1 percent over line, load and temperature, 0.2 percent typical at 25 degrees
Dropout on the main input55 mV typical and 100 mV maximum on the current silicon in the VQFN body at 1.5 A
Dropout on the bias input1.4 V on the legacy silicon and 1.43 V on the current one at 1.5 A with the main input tied to bias
Bias current1 mA typical and 2 mA maximum at full load
Soft startRamp time set by a capacitor from the SS pin to ground, monotonic by specification
Power goodOpen drain, tracks the feedback pin, usable as a sequencing signal for another rail
Output capacitorStable with any capacitor of 2.2 microfarad or larger on the current silicon
Order codeTPS74201RGRR, VQFN twenty pin 3.5 mm by 3.5 mm, 500 pieces on a large reel, tin finish, level 3, 168 hour floor life, marking TPS74201

Two chip generations again, and the capacitor rule changes

The legacy silicon in this family is stable with any output capacitor or with none at all, and the current silicon needs at least 2.2 microfarad. That is a reversal of the usual direction and it is the single most important line in the document for a customer who is replacing parts on an existing board. A board built around the legacy chip with no output capacitor will oscillate with a current silicon part, and the oscillation will look like a board problem rather than a silicon change.

The electrical differences are small and they all point the same way. Dropout falls from 60 mV to 55 mV typical at 1.5 A, line and load regulation improve, and the bias dropout moves from 1.40 V to 1.43 V. The accuracy is unchanged at 1 percent over temperature. The quiescent path is where the generations differ most in practice, since the bias current figure is specified at full load and both chips sit near 1 mA typical, so a rail that is on but idle draws about the same either way.

The 500 piece reel and the floor life

The addendum row for this body prints 500 pieces on a large reel, tin finish and moisture level 3 with a 168 hour floor life, while the five millimetre RGW body prints 3000 pieces at level 2 with a one year floor life. So the small body arrives in a smaller reel and with a shorter floor life, which affects both the feeder setup and the storage rule on the line. A production run that needs ten thousand pieces will be opening twenty reels of this body, and each one starts a 168 hour clock when it is opened.

The larger RGW body is the same die and the same pinout in a different land pattern, so the choice between them is a board decision made once and a purchasing decision made every time. Where the board can take the five millimetre body, the larger reel and the longer floor life are worth having.

Where this part fits

Network attached storage, rack servers, network interface cards and merchant power supplies are the applications in the document, which is the language of a board that powers an FPGA or an ASIC core rail and needs the sequencing. The notes we keep on sequencing and rail order are under power management cross reference, and the incoming check that catches a chip generation change before the board is built is in incoming inspection plan.

Before a purchase order, and the questions that come up

Check the dissipation at the intended input. At 1.5 A and 1.0 V out from a 1.8 V input the part burns 1.2 W, which the twenty pin body handles on a board with a ground plane. At 3.3 V in the same rail burns 3.45 W and needs copper and airflow. The part is specified for a 125 degree junction and the thermal numbers are in the document, so the calculation is straightforward, but it has to be done.

What sets the soft start time? The external capacitor and the fixed charging current, and the document gives the relationship. A rail that has to come up in a defined window uses the capacitor value, not the enable timing.

Can the power good output drive another regulator's enable directly? It is open drain, so it sinks when the rail is bad and needs a pull up to the rail of the device it drives. Driving a pin on a higher rail through a pull up is fine; driving one on a lower rail is not, because the open drain cannot pull below ground and the two rails may not be sequenced in the order assumed.

Does the bias pin need its own capacitor? Yes, a small ceramic close to the pin, and the document gives the value in the application section.