Contact Us

TPS62065QDSGRQ1

Brand: Texas Instruments
Texas Instruments TPS62065QDSGRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62065QDSGRQ1 — Power Management & Signal Chain | Superb Automation

TPS62065QDSGRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62065QDSGRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62065QDSGRQ1 2 A automotive buck at 3 MHz in a 2 mm by 2 mm SON

The TPS62065QDSGRQ1 is the AEC-Q100 grade 1 member of the TPS6206x-Q1 family, a 2.9 V to 6 V synchronous step down converter that delivers 2 A from an 8 pin WSON body of 2 mm by 2 mm with an exposed thermal pad. Both FETs sit inside the package, the oscillator runs at 3 MHz nominal, and the MODE pin chooses between a forced PWM behaviour and an automatic PWM to PFM transition at light load. There is no power good output on this member, which is the one feature that separates it from the TPS62067-Q1 in the same document.

Control is a fast response voltage mode loop with input voltage feedforward rather than a current mode scheme, which is why the load regulation figure is quoted as 0.5 %/A and the line regulation as 0 %/V on the electrical table. The feedback reference is 600 mV with a 1.5 per cent window in PWM, so the output is set by two resistors from the FB pin and does not need an external compensation network. On resistance is 120 milliohm typical and 180 milliohm maximum for the high side at 3.6 V input, and 95 milliohm typical with 150 milliohm maximum for the low side at 5 V input. Those two figures, not the 2 A headline, decide how warm the part runs at the top of its range.

Two details matter more than the front page suggests. In PFM the internal reference is deliberately raised to 1.01 times its PWM value, so the output sits about 1 per cent higher at light load than at heavy load, which is a real step on a rail that feeds a comparator threshold or an ADC reference buffer. And the thermal shutdown sits at 150 degrees junction, only 25 degrees above the 125 degree junction limit of the grade 1 part, so a converter that is comfortably inside its current rating can still fold back when the ambient climbs inside a sealed enclosure.

Key parameters from the SLVSCM3B document

Input range2.9 V to 6 V, aimed at 5 V and 3.3 V system rails
Output current2 A from an integrated high side and low side FET pair
Reference600 mV in PWM with a 1.5 per cent window, raised to 1.01 times that value in PFM
Switching frequency3 MHz nominal, 2.6 MHz to 3.4 MHz across the production spread
High side resistance120 milliohm typical and 180 milliohm maximum at 3.6 V input
Low side resistance95 milliohm typical and 150 milliohm maximum at 5 V input
Quiescent current18 microamp with no load in PFM at 25 degrees
Shutdown current0.1 microamp typical and 5 microamp maximum with the enable pin at ground
RegulationLine 0 %/V, load 0.5 %/A, quoted at the FB pin
Thermal shutdown150 degrees junction on the way up, with hysteresis on the way down
QualificationAEC-Q100 grade 1, minus 40 to 125 degrees junction, HBM classification level 2
Package8 pin WSON, 2 mm by 2 mm, DSG body with exposed thermal pad

What 3 MHz does to the rest of the rail

At 3 MHz the inductor for a 2 A rail lands near 1 microhenry, which is a 2 mm by 1.6 mm moulded part rather than the 4 mm by 4 mm component a 1 MHz converter needs. The output capacitor can be a single 10 microfarad ceramic in an 0805 body because the ripple current is delivered at three times the rate. Take 5 V in and 1.8 V out: the duty cycle is 0.36, and the peak to peak inductor ripple is 1.8 V times 0.64 divided by 1 microhenry times 3 MHz, which comes to about 0.38 A or 19 per cent of the rated load. A 1.5 microhenry part drops that to 13 per cent and costs nothing in board area.

The price is switching loss. The gate charge of the two FETs and the drain capacitance of the switch node are paid three million times a second whether the load is 2 A or 20 mA, which is why this part is not the one to pick for a rail that idles. It is the one to pick when the board is small and the load is steady. It also puts the carrier at a frequency that is easy to filter: a 3 MHz fundamental with its harmonics sits well above the audio band and above the intermediate frequencies used by most radio front ends, so a small ferrite bead on the input is enough to keep the switch node out of a receiver chain.

The 6 V input ceiling is the other consequence of the architecture. This is a 5 V rail part, not a 12 V part. On an automotive board it belongs behind a pre regulator or on a rail that is already stepped down, and the load dump event that drives a 12 V bus to 40 V has to be handled upstream by something else entirely.

Where this part fits

Automotive clusters, camera modules, sensor rails behind an ADAS processor and any 5 V or 3.3 V domain that needs 2 A in a 2 mm by 2 mm footprint with grade 1 qualification. The forced PWM setting is the one to use when the rail feeds a radio or an analog front end, and the automatic PFM setting is the one to use when the board has a standby current budget. Our desk keeps the family comparison and the substitution notes for this class of automotive buck, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

The DSG body carries the exposed pad on the underside and the pad has to be soldered to a copper island that is connected to ground, otherwise the 2 A rating is a paper number. The 3 MHz switching means the input capacitor has to be within 2 mm of the PVIN and PGND pins, and the return path from the output capacitor has to come back to the same ground island rather than through a plane split. A board that was prepared for a 1 MHz part in a SOT-23 body will not be quiet with this device dropped into it, even though the pin functions look similar.

Check the grade on the order line. The -Q1 suffix and the grade 1 qualification are what make this part usable at 125 degrees junction, and a plain TPS62065 from the industrial family will not carry the same temperature guarantee. Check the MODE strap as well, since the pin decides between two behaviours that both look correct at full load on a bench, and a floating pin is not one of the allowed states. See incoming inspection plan for the marking and reel check we run on a 2 mm by 2 mm SON body.

Questions that come up on this part

Can it run from a 12 V rail, is the first question, and the answer is no. The recommended input range stops at 6 V and the absolute maximum is only slightly above it, so a 12 V bus will destroy the part on the first application of power. The second question is whether the missing power good pin is a problem. It is not a problem if the downstream device is sequenced by a supply monitor, and it is a problem if a processor reset depends on a PG signal, in which case the TPS62067-Q1 in the same family carries the open drain output and the same footprint family.

The third question concerns the PFM reference offset. A customer who measures 1.81 V on a 1.8 V rail at no load and 1.79 V at 2 A is seeing the 1.01 times reference, not a fault. If the application cannot accept that step, strap the MODE pin for forced PWM and accept the higher quiescent current, which is the trade this device was built around.