ADUM3401ARWZ
Product Specifications
ADUM3401ARWZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADUM3401ARWZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADuM3401ARWZ: quad isolator, three channels forward and one back, 1 Mbps grade
The ADuM3401ARWZ is a four channel digital isolator in a 16-lead wide body SOIC, three channels from side 1 to side 2 and one channel back, rated -40 to +105 C. Like the dual version it is the ESD hardened generation, with extra provisions for IEC 61000-4-x testing, and it carries an output enable so the isolated side can be parked. The ARW suffix is the 1 Mbps grade of a family whose headline rate is 90 Mbps, which is the first thing to check against a timing budget.
Published values
| Parameter | Value |
|---|---|
| Channels | Four, three inputs on the VDD1 side and one input on the VDD2 side |
| Maximum data rate | 1 Mbps on ARW, 10 Mbps on BRW, 90 Mbps on CRW |
| Propagation delay | 50 ns typical, 70 ns typical at 3.3 V, 100 ns maximum on this grade |
| Pulse width distortion | 40 ns maximum on this grade, 3 ns on BRW and CRW |
| Minimum pulse width | 1000 ns on this grade, 100 ns on BRW, 11.1 ns on CRW |
| Propagation delay skew | 50 ns between units on this grade |
| Channel to channel matching | 50 ns codirectional and opposing on this grade |
| Supply | 3.0 V to 5.5 V on either side |
| Supply current | 1.4 mA per channel maximum at 0 to 2 Mbps on 5 V, 0.9 mA on 3.3 V |
| Isolation | UL 1577 2500 V rms for one minute, VIORM 560 V peak |
| Approvals | IEC/EN/CSA 62368-1, IEC/CSA 60601-1, 61010-1, CQC, VDE 0884-17 |
| Package | 16-lead SOIC_W, option RW-16, tube of 47 or reel of 1000 |
| Temperature | -40 C to +105 C across all grades |
The 90 Mbps figure is the C grade, and the timing budget shows why
A 100 ns maximum delay is nine bit periods at 90 Mbps, so the ARW code cannot carry that clock at all: its own minimum pulse width is 1000 ns, which is longer than a whole 90 Mbps bit. The CRW code in the same 16-lead body reaches 90 Mbps with an 11.1 ns minimum pulse and a 45 ns maximum delay. Two reels, one footprint, and a specification that differs by a factor of ninety.
Where this becomes expensive is a late change: a customer who has already laid out the socket and validated an ARW part, then asks for a faster interface, gets a part that fits but does not meet the new timing. The substitution is legitimate only when the faster grade is the one on the drawing and the board has been re-tested with it.
Output enable, and the channel that runs backwards
The enable pin puts the outputs into high impedance, which is what a board needs while a controller is held in reset and the far side is already powered. It has to be driven; a floating enable is not a defined state, and a socket built for a part without an enable will leave the pin open.
The single reverse channel is the other detail that catches a copy of a board file. A 3400 has four inputs on side 1 and none back, so a fault line returned from the isolated side will not pass on a 3400. If the drawing calls for a return path, the 3401 is the minimum member of the family that provides it.
Two pages worth reading before a purchase order goes out are the ADI second source page and one stop BOM sourcing; the first lists what else fits the socket, the second is the test sequence for a drop in, and how to verify a drop in replacement covers the case where the shortage is already on the line.
Two questions buyers ask
Is the ARW code fast enough for a 10 MHz SPI clock? No. This grade runs 1 Mbps with a 1000 ns minimum pulse width. The BRW code is 10 Mbps and the CRW code 90 Mbps, both in the same 16-lead body.
Can two grades of this family sit on one board? They will fit the same socket. The timing budget then has to be written for the slower part, which is usually worse than fixing one code and ordering it in the quantity that earns the better price.