ADXL346X-RL7
Product Specifications
ADXL346X-RL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADXL346X-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADXL346X-RL7: a 13-bit accelerometer that runs on 23 uA
The ADXL346X-RL7 is a three axis digital accelerometer with selectable 2 g, 4 g, 8 g and 16 g ranges, 13-bit resolution at 16 g and a scale factor of 4 mg per LSB that stays the same across all four ranges. In measurement mode it draws as little as 23 uA at 2.6 V, and 0.2 uA in standby. The package is 3 mm by 3 mm by 0.95 mm, which is why it appears in handheld instruments, asset trackers and medical monitors where the accelerometer is not allowed to be the biggest part on the board.
Published values
| Parameter | Value |
|---|---|
| Axes and range | 3 axes, 2 g / 4 g / 8 g / 16 g selectable |
| Resolution | 13-bit at 16 g, 4 mg per LSB in all ranges |
| Supply current, measurement | 23 uA at 2.6 V typical |
| Supply current, standby | 0.2 uA typical |
| Interfaces | SPI 3-wire or 4-wire, and I2C |
| Output format | 16-bit twos complement |
| Internal buffer | FIFO to reduce host reads |
| Built in functions | Tap and double tap, activity and inactivity, free fall |
| Shock survival | 10,000 g |
| Package | 16-lead LGA, 3 mm x 3 mm x 0.95 mm |
Resolution that does not fall with range
Many accelerometers keep a fixed 10-bit output, so switching from 2 g to 16 g makes each count eight times coarser. This part holds 4 mg per LSB in every range, so a tilt measurement made at 2 g and a shock measurement made at 16 g use the same scale factor and the same firmware conversion. On a product that switches range at runtime that removes a calibration step and a source of arithmetic error in the application code.
The 4 mg per LSB figure also sets what the part can resolve in tilt. A 1 degree change in tilt is about 17 mg, so the converter has roughly four counts of movement per degree, which is enough for a level or an orientation function and not enough for an inertial navigation grade measurement.
The FIFO is what keeps the average current down
Reading the part on every sample keeps the host awake, and on a battery product the host current is usually far larger than the sensor current. The internal FIFO lets the sensor collect a burst of samples while the host sleeps, then wake it once to read the whole block, so the average system current falls even though the sensor itself is still sampling. Any power calculation that only looks at the 23 uA figure and ignores the host wake up rate will be optimistic.
Motion functions that run without the host
Activity, inactivity, tap, double tap and free fall are decided inside the part against thresholds set over the serial bus. On an asset tracker that means the host can stay in its deepest sleep until the part raises an interrupt, which is the difference between a two year and a two month battery life on the same cell.
For a board that has to keep running while a reel runs out, one stop BOM sourcing is where the family alternatives sit, vendor consolidation is the check list before a substitute goes in, and component lead time solutions is how a gap is covered without a new line item.
Two questions buyers ask
Does the ADXL346 need an external clock? No, it runs from its own oscillator. An external clock is only used where several sensors have to be synchronised to the same time base.
Is the RL7 packing code a different part? No, it is a reel packing suffix on the same body. The electrical specification is unchanged and the reel label carries the lot and date code.