Contact Us

ADUM3160BRWZ

Brand: Analog Devices
Analog Devices ADUM3160BRWZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADUM3160BRWZ — Analog & Mixed-Signal ICs | Superb Automation

ADUM3160BRWZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADUM3160BRWZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADuM3160BRWZ: isolating an upstream USB port at 12 Mbps

The ADuM3160BRWZ is a USB port isolator for the upstream facing port, in a 16-lead wide body SOIC, rated -40 to +105 C and supplied in tubes of 47. It passes full speed and low speed traffic, 12 Mbps and 1.5 Mbps, and it decides the direction of the D+ and D- lines packet by packet, which is the part of USB isolation a plain digital isolator cannot do. Boards that need a USB connector to survive a mains referenced front end use this part, and the grade letter is where the automotive version separates.

Published values

ParameterValue
FunctionUpstream facing USB port isolator, USB 2.0 compatible
Data rates12 Mbps full speed and 1.5 Mbps low speed
Bus voltage4.5 V to 5.5 V VBUS on either side, regulated internally
Upstream supply current8 mA maximum at 12 Mbps, 7 mA at 1.5 Mbps, 2.3 mA idle
Propagation delay, full speed20 ns typical, 60 ns typical at 3.3 V, 70 ns maximum
Propagation delay, low speed325 ns typical at 3.3 V
Jitter, full speed3 ns next transition, 1 ns paired transition
ESDClass 3A contact per ANSI/ESD STM5.1-2007
IsolationUL 1577 2500 V rms for one minute, VIORM 645 V peak
Transient immunityAbove 25 kV per microsecond
Package16-lead SOIC_W, option RW-16, tube of 47 or reel of 1000
Temperature-40 C to +105 C
AutomotiveThe W code, ADuM3160WBRWZ, is the AEC-Q100 qualified version

Two data rates, two very different delays

Full speed traffic crosses the barrier in 70 ns worst case. Low speed traffic takes 325 ns typical, which is more than four and a half times longer, and that figure is a typical value rather than a maximum. A device that enumerates at 1.5 Mbps therefore has far less timing margin than the same device running at 12 Mbps, and the difference does not appear anywhere in the headline description.

The jitter numbers move with the rate as well: 3 ns on the next transition and 1 ns on a paired transition at full speed. Those are the figures that matter when a downstream hub and a cable are added to the link, because the isolator is only one term in the eye.

Upstream only, and what that means for a hub

The part isolates the port that faces the host, not the ports that face devices. Its internal logic watches which side is driving, so a peripheral can hold the bus in its idle state and the isolator follows. The pull-up resistor control is isolated too, which lets the peripheral decide when it connects rather than when power appears.

The 5 kV version of the same function is the ADuM4160, in the same RW-16 footprint, and it adds 60601-1 and 61010 listings. Moving a board from 3160 to 4160 is a reel change and a re-read of the creepage table, not a board change, which is worth knowing when a medical customer asks for more than 2.5 kV after the boards are already ordered.

For a board that has to keep running while a reel runs out, the pin to pin cross reference is where the family alternatives sit, medical device components is the check list before a substitute goes in, and how to verify a drop in replacement is how a gap is covered without a new line item.

Two questions buyers ask

Will this pass a 480 Mbps high speed USB link? No. It carries 12 Mbps full speed and 1.5 Mbps low speed. A high speed link needs a different approach, either an isolator built for 480 Mbps or a hub that re-times the link on each side.

Is the ADuM4160 a drop in replacement for this part? It shares the RW-16 body and the same function, and it raises the rating to 5 kV with 60601-1 and 61010 listings. The current table and the creepage still have to be checked, so it is a reel change plus a re-test rather than a straight swap.