Contact Us

TPS62056DGSR

Brand: Texas Instruments
Texas Instruments TPS62056DGSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62056DGSR — Power Management & Signal Chain | Superb Automation

TPS62056DGSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62056DGSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62056DGSR: an 800 mA step down converter with a fixed 3.3 V output in a 3 mm by 3 mm MSOP body

TPS62056DGSR is a synchronous step down converter with integrated P channel and N channel switches, a fixed 3.3 V output and a power save mode that holds the quiescent current at 12 microamp in a VSSOP (DGS) body of 10 pins. It runs from 2.7 V to 10 V, switches at 850 kHz nominal and can be locked to an external clock between 600 kHz and 1.2 MHz, reaches 95 per cent efficiency, and keeps the shutdown current under 2 microamp. The free air temperature range is minus 40 C to 85 C.

Order code and package

TPS62056DGSRVSSOP (DGS) body, 10 pins, 3.00 mm by 3.00 mm, 2500 pieces on a large reel, the fixed 3.3 V member of the family
TPS62056DGSthe same body in a tube of 80 pieces, the row a hand load or a small build orders
TPS62056DGSG4the same string with the G4 suffix, same body and same packing, the row to order when the finish has to be stated explicitly
TPS62050DGSRthe adjustable member, 0.7 V to 6 V set by a divider, 2500 pieces on a large reel, the row when the rail is not 1.5 V, 1.8 V or 3.3 V
Markingthe addendum carries different markings across the family, so the reel label rather than the body is the reliable way to tell a 3.3 V part from a 1.8 V part
Packing2500 pieces on the large reel and 80 in a tube, both in the same 10 pin body

Electrical parameters that decide the application

Input voltage2.7 V to 10 V, which covers one lithium cell at the low end and a 9 V rail at the top
Output current800 mA continuous from the integrated switches
Output voltage3.3 V fixed on this string, with 1.5 V and 1.8 V members in the same body and an adjustable range of 0.7 V to 6 V on the TPS62050
Switching frequency850 kHz nominal, which is why the inductor and the output capacitor can both be small
Synchronisationan external clock between 600 kHz and 1.2 MHz can lock the converter, which keeps the switching tone out of a radio band
Quiescent current12 microamp typical, and under 2 microamp in shutdown
P channel resistance400 milliohm typical and 650 milliohm maximum at an input above 5.4 V, which is the conduction loss at 800 mA
N channel resistance300 milliohm typical and 450 milliohm maximum, the synchronous rectifier side of the bridge
Switch current limit1.2 A typical, which is the ceiling the start up current and the load transients run into
Duty cycle100 per cent maximum, so the part passes the input through when the battery falls close to the output
Modespower save mode at light load and forced fixed frequency PWM for low noise operation
Temperatureminus 40 C to 85 C free air, which is narrower than the industrial parts in the same body size

Family variants and how they differ

TPS62050the adjustable member, 0.7 V to 6 V, listed with the enhanced option in the family table
TPS62051the adjustable member listed as standard, the same range without the enhanced option
TPS620521.5 V fixed, the rail for an older logic family
TPS620541.8 V fixed, the most common rail in the family
TPS620563.3 V fixed, the member on this page, used where the load needs a 3.3 V rail from a battery or a 5 V bus

Points to check before this part goes on a BOM

The fixed output is set inside the package. There is no feedback divider on the 3.3 V member, so the rail cannot be moved and the accuracy is the device accuracy.

The input range is wide for a battery converter. 2.7 V to 10 V covers a single cell, a two cell pack and a 9 V battery, which is why the same body appears in instruments that run from very different supplies.

The 100 per cent duty cycle matters at the end of a discharge. When the battery falls to the output voltage the converter stops switching and passes the input through, so the rail follows the battery down instead of dropping out.

The temperature range is 85 C, not 125 C. A board that runs the part near its current limit in a warm enclosure has less margin than the same circuit built with an industrial grade part.

The external clock is the reason this family appears in radio products. Locking the switching frequency to a system clock keeps the converter from putting a tone inside a receive band.

Reading the family table before ordering

The five members share a body and a pinout, and the difference is the output voltage and the option column. A BOM that names TPS62054 and a purchasing list that shows TPS62056 will build a board that runs, but at 3.3 V instead of 1.8 V, and the fault looks like a dead load rather than a wrong part.

The adjustable member needs two resistors and the fixed members do not, so a board laid out for the fixed part has no place for the divider. That is the reason the fixed strings, not the adjustable one, are usually specified for a 3.3 V rail.

The 800 mA figure also depends on the input voltage. At 2.7 V in and 3.3 V out the part cannot regulate, because the output is above the input, and it passes the input through instead. The useful window starts once the input is above the output by the dropout the switches set, which at 800 mA is a few hundred millivolts rather than a few tens.

The inductor choice follows the 850 kHz. A 2.2 microhenry part keeps the ripple small at 800 mA, and a larger value slows the transient without helping the efficiency any further. Most boards in this family use the same inductor across all five output voltages, which is why the family is easy to substitute inside a product line.

The shutdown pin is not the same as the enable divider on a larger converter. It is a logic input with a fixed threshold, so a system that needs an undervoltage lockout above the internal one has to add a comparator rather than a resistor divider.

Where this order code fits

It fits a handheld instrument or a battery powered terminal that needs a 3.3 V rail at up to 800 mA from a single cell or a 5 V bus. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the 3.3 V output be adjusted? No. This string is fixed at 3.3 V. The TPS62050 in the same body is the adjustable member and covers 0.7 V to 6 V with an external divider.

What happens when the battery falls below 3.3 V? The converter reaches 100 per cent duty cycle and passes the input through, so the output follows the battery down instead of dropping out at a fixed threshold.

Why does the switching frequency matter? 850 kHz keeps the inductor and the capacitor small, and the ability to lock to an external clock between 600 kHz and 1.2 MHz keeps the switching tone out of a radio band.

Is the part rated for 125 C? No. The free air range is minus 40 C to 85 C, so a warm enclosure needs a thermal check at the load current rather than an assumption from the body size.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.