Contact Us

AD8227ARZ-R7

Brand: Analog Devices
Analog Devices AD8227ARZ-R7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8227ARZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

AD8227ARZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8227ARZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD8227ARZ-R7: 24 nV of Noise and the 250 kHz That Comes With It

The AD8227ARZ-R7 is a wide supply range instrumentation amplifier from Analog Devices with a rail-to-rail output. The published summary gives a gain range of 5 to 1000 set by one external resistor, an input voltage range that extends below ground, inputs protected beyond the supplies, single supply operation from 2.2 V to 36 V or dual supplies from +/-1.5 V to +/-18 V, 250 kHz of bandwidth at a gain of 5, 24 nV per root Hz of input noise, 350 uA of typical supply current, a specified range of -40 C to +125 C, and an 8-lead SOIC or MSOP package. The ARZ suffix is the 8-lead SOIC in tape and reel, in the A grade.

250 kHz of bandwidth is 12 uV of noise

Noise density on its own does not answer a buyer's question, because the noise that reaches the converter is the density multiplied by the square root of the bandwidth actually used. At the full 250 kHz the input referred noise is 12.0 uV rms. Against a 10 mV full scale sensor that is 58.4 dB of signal to noise, which is under 10 effective bits whatever converter follows. Limit the bandwidth to 25 kHz with a filter and the same part gives 3.8 uV and 68.4 dB. At 2.5 kHz it gives 1.2 uV and 78.4 dB.

At the output of a gain of 5 stage the 250 kHz figure becomes 60 uV rms, which is close to one 16-bit LSB on a 5 V range. A chain that puts a 16 bit converter behind this amplifier and runs it at full bandwidth cannot collect 16 bits from the amplifier side, and that is a decision about the filter, not about the grade of the part.

A minimum gain of 5 means this is not a buffer

One resistor sets the gain, and the range starts at 5. Nothing in the published summary offers a unity gain configuration, so the part cannot be used as a buffer or as a difference amplifier at a gain of one. Where a chain needs both, the buffer is a separate device, and the resistor that sets the in-amp gain is chosen from the gain table in the datasheet rather than calculated from a single formula in this page. Buyers who ask for an in-amp and then specify a gain of 1 are usually looking at a different product family.

The A grade against the 100 dB CMRR headline

The product overview quotes common mode rejection of 100 dB minimum at a gain of 5, and the same line states that this is the B grade figure. The part on this page is an A grade, an AD8227ARZ, so a budget that quotes 100 dB is quoting the grade above the one being bought. The grade column of the datasheet is where the two figures separate, and on a production line the difference between them is a screening step that nobody wants to discover at incoming inspection.

Where the wide supply earns its place

At 36 V the 350 uA quiescent current is 12.6 mW, and at 2.2 V it is 0.77 mW, so the same part spans a loop powered transmitter and a battery instrument. Inputs protected beyond the supplies means a sensor that is energised before the amplifier does not damage it. An input range that goes below ground means a shunt or a thermocouple return can sit at the negative rail without a charge pump behind it.

Published figures

ParameterValue
Gain5 to 1000, one external resistor
Supply2.2 V to 36 V single, +/-1.5 V to +/-18 V dual
Bandwidth at gain of 5250 kHz
Input noise24 nV per root Hz
Noise over 250 kHz12.0 uV rms, derived here
CMRR at gain of 5100 dB minimum, B grade
Supply current350 uA typical
Temperature range-40 C to +125 C, specified
Package8-lead SOIC, ARZ, tape and reel

Selection notes

  • Check the grade letter before quoting the common mode rejection, because the headline figure belongs to the B grade.
  • The limit on resolution at full bandwidth is the amplifier noise, so an external filter ahead of the converter is part of the signal chain cost.
  • Input protection beyond the supplies is a system level saving: no clamp diodes and no series resistors on the sensor side.
  • An input range below the negative rail allows a single supply build where the sensor return is the supply return.
  • The ARZ code is SOIC and the RMZ code is MSOP in the same grade, so the footprint determines the order code rather than the performance.

Buyer questions

Is the 100 dB common mode rejection the figure I get on the A grade? No. The overview attaches 100 dB minimum to the B grade. The A grade is the wider tolerance grade and its datasheet column has to be read before that number goes into a budget.

Can it run from a single 3.3 V rail? Yes, the minimum single supply is 2.2 V and the output swings rail to rail, so a 3.3 V system is inside the range. The trade is bandwidth: 250 kHz at a gain of 5 leaves little room for a fast channel.

Category page: Analog and mixed-signal ICs. For alternatives by function see amplifier cross reference, and for parts that have reached end of life see obsolete part cross reference.

AD8227ARZ-R7: 24 nanovolts against a bridge that only makes 2.4

A 350 ohm strain gauge bridge at room temperature produces about 2.4 nanovolts per root hertz of thermal noise from its own resistance, and this amplifier contributes 24, so the amplifier dominates the noise budget by a factor of ten. That is worth knowing before money is spent on a lower noise amplifier: the source sets a floor that no front end can go below, and at 350 ohm the floor is far under the amplifier. Where the amplifier's 24 nV does matter is at low signal levels and wide bandwidths, and there the filter behind it is the only lever that costs nothing.

ItemValueWhat it decides
Noise24 nV per root hertz12 uV over the full 250 kHz at a gain of 5
Source floor2.4 nV for a 350 ohm bridgeThe amplifier, not the bridge, sets the noise
Gain5 to 1000 by one resistorA minimum of 5 means it cannot be used as a buffer
Supply current350 uA typical1.75 mW at 5 V, a tenth of what a 350 ohm bridge itself draws
Supply range2.2 V to 36 V singleRuns from the same 24 V rail as industrial sensors
Input rangeExtends below ground, protected beyond the suppliesA current sense on a high side can sit at the negative rail and survive

The bandwidth is the noise decision

Twenty four nanovolts per root hertz becomes 12 uV when integrated over 250 kHz, 3.8 uV over 25 kHz and 1.2 uV over 2.5 kHz. The signal from a bridge at full scale is often 10 mV, so the signal to noise ratio runs from 58 dB at full bandwidth to 68 dB with a 10 to 1 filter and 78 dB with a 100 to 1 filter. A 16 bit converter behind an amplifier at full bandwidth cannot collect 16 bits from the amplifier side, and that is a filter decision rather than a part grade decision.

Three hundred and fifty microamps is not the load

The amplifier draws 350 uA, which is 1.75 mW, and a 350 ohm bridge on a 5 V excitation draws 14.3 mA, eight times the amplifier. In a battery instrument the bridge excitation is what sets the life, and the usual method is to pulse it for a few milliseconds per reading rather than to run it continuously, which makes the amplifier's 1.75 mW the standing cost. That is the number to put in the power budget, and it applies whether the bridge is on or off.

What the wide supply buys

Operation from 2.2 V to 36 V single and plus or minus 1.5 V to plus or minus 18 V dual means the same part sits on a 3.3 V logic board and on a 24 V industrial rail without a regulator in front of the sensor. The inputs extend below ground and are protected beyond the supplies, which is what allows a high side shunt or a sensor that is powered down while the amplifier is still on. The range is listed on the analog and mixed signal line card, a pin compatible alternative is checked through pin to pin cross reference, and stock is confirmed on the lead time page.

Request Quote — In Stock, 100% New & Original, Full Warranty