Contact Us

AD5060ARJZ-2500RL7

Brand: Analog Devices
Analog Devices AD5060ARJZ-2500RL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD5060ARJZ-2500RL7 — Analog & Mixed-Signal ICs | Superb Automation

AD5060ARJZ-2500RL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD5060ARJZ-2500RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD5060ARJZ-2500RL7: 16 Bits, 1 LSB of INL, in an SOT-23

The AD5060ARJZ-2500RL7 is a single channel 16-bit voltage output digital to analog converter from the nanoDAC family of Analog Devices, in an 8-lead SOT-23. It guarantees plus or minus 1 LSB of integral nonlinearity maximum, including the output buffer, and total unadjusted error under 1 mV. The reference is external and feeds an on-chip reference buffer, the three-wire serial interface runs at clock rates to 30 MHz and is compatible with SPI, QSPI, MICROWIRE and DSP ports, and a power-on reset circuit brings the output to zero or to mid scale depending on the model and holds it there until a valid write arrives. Three power-down modes bring the current to 1 uA at 5 V with software selectable output loads, and the power-up glitch is small by construction.

One LSB is 38 uV, and one millivolt is 26 LSB

With a 2.5 V reference one LSB at 16 bits is 38.15 uV, and with a 5 V reference it is 76.3 uV. The 1 mV total unadjusted error is 26 LSB at the 2.5 V reference, so the linearity specification is not the accuracy of the system: the reference tolerance, its drift and the offset of the output buffer dominate the DC error. A circuit that needs a guaranteed absolute output has to start from the reference and work backwards, and a board that only needs monotonic trim can live with the 1 LSB linearity and a looser reference.

Thirty megahertz puts a 24-bit frame in 0.8 us

The interface clock is fast enough that the frame time is not the limit; what limits the update rate is the settling of the output amplifier and the recovery of the reference buffer after each code change. For a control loop that updates at a few kilohertz this is irrelevant, and for a waveform generator the settling time in the data sheet, not the clock rate, decides the usable sample rate. The on-chip reference buffer is there because the external reference has to drive a switched load at the DAC's update rate, and a reference without enough drive will show code dependent settling that looks like distortion.

The power-on state is a model option, and it matters

Some models power up to zero volts and some to mid scale. In a loop that drives a valve, a heater or a bias point, mid scale at power-up is half of full output applied before the processor has run a single instruction. The order code decides which one is on the board, so the power-on state has to be read from the ordering table rather than assumed, and a system that cannot tolerate the mid scale state needs either the zero scale model or a hardware clamp that holds the actuator off until the first valid write.

ParameterPublished valueWhat it decides
Resolution16 bits38.15 uV per LSB on 2.5 V
Linearityplus or minus 1 LSB maximumIncludes the output buffer
Total unadjusted errorUnder 1 mV26 LSB, so the reference dominates
ReferenceExternal, buffered on chipDrive strength matters at the update rate
Interface3-wire, 30 MHz24-bit frame in 0.8 us
Power down1 uA at 5 V, three modes5 uW parked
Power-on resetZero or mid scale by modelMid scale applies half output at power-up
Package8-lead SOT-23Smallest footprint in the family

Does it need an external reference?

Yes. There is a reference buffer on chip but no reference, so the accuracy of the output is the accuracy of whatever is connected to the REF pin. A 2.5 V reference with 0.1 percent initial tolerance contributes 2.5 mV of full scale error, which is already larger than the converter's 1 mV total unadjusted error, and the drift of that reference adds on top across temperature. A ratiometric arrangement, where the same reference sets the measurement and the output, cancels the reference from the transfer function.

Can a 12-bit part in the same footprint be replaced by this one?

Electrically the 16-bit device fits an 8-lead SOT-23 socket, but the code scaling changes by a factor of sixteen and the settling time is longer, so firmware that writes a 12-bit word into a 16-bit register produces an output at one sixteenth of the intended value. The verification steps for a resolution change of that kind are on the drop in replacement page, the matching converters and references are on the ADC and DAC cross reference, and the complete index is the analog and mixed-signal index.

Request Quote — In Stock, 100% New & Original, Full Warranty