ADUM7223ACCZ-RL7
Product Specifications
ADUM7223ACCZ-RL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADUM7223ACCZ-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADUM7223ACCZ-RL7: A 4 A Half-Bridge Driver With 60 ns Across the Barrier
The ADUM7223ACCZ-RL7 is an isolated half-bridge gate driver from Analog Devices in a 5 mm by 5 mm 14-lead LGA. It puts a digital isolator and a gate driver in one package, with two independent channels that can drive the high side and the low side of a bridge. Peak output current is 4 A, the working voltage is 565 V peak from either output to the input and 700 V peak between the two outputs, the input logic runs from 3.0 V to 5.5 V, the output drive runs from 4.5 V to 18 V, and the maximum switching frequency is 1 MHz. Propagation delay is 60 ns maximum and channel to channel matching is 7 ns maximum, common mode transient immunity is above 25 kV per microsecond, the output defaults low, and the part is rated for a 125 C junction temperature.
565 V peak is 400 V RMS, and that is a working voltage
The isolation figure is a working voltage, not a one minute withstand test, so it describes what the barrier can hold continuously rather than what it survives once. 565 V peak is 400 V RMS, which covers a 380 V DC bus or a 220 V AC drive with margin, and the 700 V peak between the two outputs is what allows the high side and the low side to sit at different potentials without a second barrier. A circuit that runs a 600 V bus is outside this device on the working voltage even though a short test would pass, and that distinction is where isolation ratings are most often read too generously.
Sixty nanoseconds at 1 MHz is six percent of the period
At 1 MHz the period is 1 microsecond, so 60 ns of propagation delay is 6 percent of it, and 7 ns of channel matching is 2.5 electrical degrees. The delay is a fixed offset that a current loop can tolerate; the matching is what sets the minimum dead time, because the two channels never switch at exactly the same instant. A dead time shorter than 7 ns cannot be guaranteed, and in practice the dead time is set well above that to cover the FET's own turn-off, which is measured in tens of nanoseconds for a large die. At 100 kHz the same 60 ns is 0.6 percent of the period and stops being interesting.
Four amps is a peak, and the gate charge decides the average current
The 4 A rating is the peak the output stage can deliver while charging a gate, so a 100 nC gate is charged in 25 ns at that current, which is the number that matters for switching loss. The average current is the gate charge times the frequency: 100 nC at 1 MHz is 0.1 A per channel, and the gate drive loss at an 18 V rail is 1.8 W per channel, so two channels at full rate dissipate 3.6 W before the driver's own quiescent current is counted. That loss sits in the gate resistors and in the driver, so the package and the copper under the LGA are part of the thermal budget, and a 125 C junction rating is not a licence to run at 125 C in a sealed enclosure.
| Parameter | Published value | What it decides |
|---|---|---|
| Peak output | 4 A | 100 nC charged in 25 ns |
| Isolation | 565 V peak working, 700 V peak channel to channel | 400 V RMS continuous |
| Propagation delay | 60 ns maximum | 6 percent of a 1 MHz period |
| Channel matching | 7 ns maximum | Sets the minimum dead time |
| Input supply | 3.0 V to 5.5 V, 3.3 V and 5 V logic | No level shifter from a 3.3 V controller |
| Output supply | 4.5 V to 18 V | Gate drive loss rises with the rail |
| Switching rate | 1 MHz maximum | 3.6 W of gate loss at 18 V |
| Common mode immunity | Above 25 kV per microsecond | Handles fast dv/dt on the switch node |
Is the undervoltage lockout on the input side or the output side?
Both. The A version has a 2.5 V lockout on the input supply and a 4.1 V lockout on the output supply, so a 5 V input logic rail starts the part but the output stage stays off until the gate drive rail is above 4.1 V. That matters at power-up: if the 12 V gate rail comes up slowly, the driver holds the output low rather than switching with a rail that is too low to turn the FET fully on, which is the failure mode that destroys FETs in a bridge. The default low output at power-up is the second half of the same protection.
What replaces a pulse transformer plus a driver?
This part, and the reason is timing: a pulse transformer based arrangement cannot pass a DC level, so it needs encoding, and the encoding is what limits the minimum pulse width and the delay matching. A single package with a 60 ns delay and 7 ns matching removes both problems and shrinks the isolated gate drive to one 5 mm square. The power and gate driver range is on the power management cross reference, the pin and package comparison against the parts it replaces is on the pin to pin cross reference, and the complete index is the analog and mixed-signal index.
Request Quote — In Stock, 100% New & Original, Full Warranty