Contact Us

TPS612997YBHR

Brand: Texas Instruments
Texas Instruments TPS612997YBHR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS612997YBHR — Power Management & Signal Chain | Superb Automation

TPS612997YBHR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS612997YBHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS612997YBHR the 1.9 A input limit member of the nanoamp boost family

The TPS612997YBHR is the highest current member of the TPS61299x family, with an average input current limit of 1.5 A minimum and 1.9 A maximum, in the same 6 ball chip scale body measuring 1.2 mm by 0.8 mm. It keeps the 95 nanoamp quiescent current and the 0.5 V to 5.5 V input range of the family, and it delivers enough current for a radio transmit burst or a small motor from a single cell.

The point of a 1.9 A input limit on a part with a nanoamp idle current is that the same converter covers both ends of the load profile. Between bursts the product sits in snooze and draws almost nothing, and during a burst the limit allows the current the load needs without pulling the cell into its cut off voltage. A converter with a lower limit would need a larger output capacitor to average the burst.

Like the rest of the family, this member starts from 0.7 V, operates down to 150 mV while the input stays above 0.7 V, and sets its output between 1.8 V and 5.5 V with an external divider. Thermal shutdown is at 150 degrees with 20 degrees of hysteresis.

Key parameters from the SLVSGS9G document

Input range0.5 V to 5.5 V, start up from 0.7 V on the non-A members
Output1.8 V to 5.5 V, set by an external divider
Input current limit1.5 A minimum and 1.9 A maximum, the largest step on the family ladder
Quiescent current95 nanoamp typical into the input pin, 4 nanoamp into the output pin
ShutdownTrue shutdown with the enable low, 60 nanoamp into the input pin
Inductor ripple350 mA typical, which sets the inductance for a given frequency
ProtectionThermal shutdown at 150 degrees with 20 degrees of hysteresis
Package6 ball chip scale, 1.2 mm by 0.8 mm, YBH body, 6000 pieces on a large reel, moisture level 1

A 1.9 A input limit in a 1.2 mm body

The current limit is on the input, so the output current depends on the conversion ratio. From 1.8 V in to 3.3 V out the ratio is 1.83, so 1.5 A of input supports about 750 mA of output before efficiency. From 0.9 V in the same limit supports about 350 mA, and that is the operating point where the thermal limit of a 1.2 mm by 0.8 mm body becomes the real constraint rather than the current limit.

The 350 mA inductor ripple figure is the starting point for the inductor value. A 1 microhenry inductor at the switching frequency used by this part produces roughly that ripple at 1.8 V in, and a larger inductance reduces the ripple but slows the burst response, which matters on a load that steps between microamps and amps.

The output capacitor has to average the burst. During a 2 A transmit pulse at 5 V out the converter supplies what the input limit allows, and the difference comes from the output bank. A 22 microfarad ceramic holds the rail within a few hundred millivolts for a pulse of a few hundred microseconds, and a smaller bank will let the rail sag into the load's undervoltage threshold.

Where this part fits

Single cell radio modules, portable meters with a transmit burst, and any product that needs a nanoamp idle current with an amp of transient capability. Our desk keeps the family ladder and the second source notes, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

Confirm the digit. The 1.9 A member and the 1.2 A member are the same body and the same die, and the four digit in the part number is the only difference on the reel label. A 1.2 A part in place of the 1.9 A part will current limit during a transmit burst and the symptom will look like a software timing problem rather than a component problem.

Confirm the inductor saturation against 1.9 A plus the 350 mA ripple, which puts the peak near 2.2 A. A 2 A inductor will saturate at the top of the limit and the current will run away into the switch. See incoming inspection plan for the receipt check on a 6 ball chip scale body.

Questions that come up on this part

Is the current limit a hard limit, is the first question. It is an average input current limit, so the peak inductor current will exceed it within a switching cycle, and the inductor has to be sized for the peak rather than for the average. The second question is whether the part can deliver 1 A at 5 V from a single cell. It cannot, because the input current at that operating point is well above the limit, and the output falls to whatever the limit supports.

The third question is about the 95 nanoamp figure at temperature. It is specified up to 85 degrees, and above that the leakage of the internal circuits rises, so a product that has to sit at 105 degrees needs a different idle current assumption.