Contact Us

UCC27284DRCR

Brand: Texas Instruments
Texas Instruments UCC27284DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC27284DRCR — Power Management & Signal Chain | Superb Automation

UCC27284DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC27284DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC27284DRCR: a 5 V UVLO half bridge driver that stays out of the way below 5 V

The UCC27284DRCR is a 3 A half bridge driver for two N channel MOSFETs with a 100 V switch node rating and a 120 V absolute maximum on the bootstrap pin. What separates it from the older 120 V family is the UVLO point: 5 V typical rather than 8 V. On a 12 V rail that difference changes when the driver starts to switch during power-up, and on a system that brings the 12 V rail up slowly, a 5 V lockout lets the bridge begin working earlier in the ramp instead of holding both outputs low until the rail is nearly settled.

The timing is tighter than the earlier parts as well. Propagation delay is 16 ns typical, rise and fall are 12 ns and 10 ns into a 1.8 nanofarad load, and the two channels match within 1 ns. The inputs and the switch node both tolerate negative voltage, minus 5 V on the inputs and minus 14 V on HS, which covers the ringing a half bridge produces at 100 V. Disabled current is 7 microamps, and the DRC body carries an enable pin that the eight pin version does not, which lets a bridge be parked while the driver rail stays up.

Key electrical data for the UCC27284DRCR

TopologyHalf bridge, two N channel MOSFETs, high side and low side inputs independent
Voltages100 V switch node rating, 120 V absolute maximum on the bootstrap pin
UVLO5 V typical lockout, both drivers held low below the threshold
Timing16 ns typical propagation delay, 1 ns typical delay matching, 12 ns rise and 10 ns fall at 1.8 nF
Drive3 A peak source and sink, 7 microamps when disabled
ToleranceMinus 5 V on the inputs, minus 14 V on the switch node, junction -40 C to 140 C

Package, marking and reel data

BodyDRC, 10 pin VSON, 3.0 mm by 3.0 mm, enable pin present
Reel3000 pieces on a large reel, 250 pieces on the small reel code DRCT
FinishSN plating, level 1 at 260 C with unlimited floor life
OptionsDRM, 8 pin VSON without the enable pin, also 3000 pieces on a large reel

Synchronous buck and secondary side rectification

The vendor lists secondary side synchronous rectification of a full bridge among the supported uses, which is where the independent inputs earn their place: the two outputs can be overlapped, because the two inputs are not interlocked. That flexibility is not available on a driver with a single PWM input, and it is the reason a synchronous rectifier stage on a 48 V output can use one part for both switches instead of two, and the 100 V node rating is what keeps that arrangement inside a single package rating rather than a pair of the smaller eight pin bodies.

The 100 V switch node rating sets the bus ceiling. A 48 V rail with 20 percent overshoot reaches 58 V, well inside the rating, while an 80 V rail with the same overshoot reaches 96 V and leaves almost nothing for the ringing that a fast turn-off produces on a board with 20 nanohenries of loop inductance. The 5 V UVLO also means a 5 V rail feeding the driver is right at the lockout, so a 12 V driver rail is the normal arrangement. Our power management cross reference page lists the drivers we hold across this voltage class.

Buyer questions on the UCC27284DRCR

Does the enable pin save power in standby? It does. Disabled current is 7 microamps, so a bridge that is not switching can be shut down without removing the 12 V rail, which is useful on a battery backed system.

Is the 8 pin version a drop-in? It is the same die in a smaller body without the enable pin, so the land pattern differs and the pin count drops. It is a substitution at the connection level, not at the board level.

Why is the UVLO 5 V rather than 8 V? It lets the driver start earlier in the rail ramp, which suits logic level MOSFETs and low voltage buses. A gate threshold above 4.5 V needs the 8 V family instead.

Availability and cross reference

This code ships 3000 pieces per reel in SN plating at level 1, and the 250 piece small reel is useful for a pilot build without opening a full reel. Because the enable pin and the body differ between the 10 pin and the 8 pin versions, we quote by body rather than by family and record the land pattern on the quotation. Our pin to pin cross reference page covers the bodies that share a footprint.