UCC27524P
Product Specifications
UCC27524P
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC27524P from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC27524P: two 5 A low side channels in a through hole body, with inputs that survive minus 5 V
The UCC27524P is the PDIP-8 member of the UCC27524 family, a dual channel low side gate driver with 5 A peak source and 5 A peak sink current, a 4.5 V to 18 V single supply and a propagation delay of 17 ns typical. Both channels are non-inverting and each has its own enable pin, ENA and ENB, which are pulled up inside the device so a board that does not need them leaves them open and the driver runs. The input thresholds are fixed at 1.9 V to 2.3 V for a high and 1.0 V to 1.4 V for a low, with 0.7 V to 1.1 V of hysteresis, and they do not move with the supply, so a 3.3 V logic signal drives the part the same way whether VDD is 5 V or 15 V.
The feature that separates this code from the rest of the low side driver market is the input rating. The pins accept minus 5 V continuously, which is what happens on a half bridge when the switch node rings below ground and the driver input is tied to a source that follows it, or when a transformer coupled gate signal goes negative. The vendor states the negative handling on the input pins, not on the outputs, and the two channels are matched to 1 ns typical so a synchronous rectifier pair or two paralleled switches switch together. The outputs are held low while VDD sits below the undervoltage lockout, which is about 4 V with 300 mV of hysteresis, and they are also held low when an input pin floats, because the pins carry internal pull up and pull down resistors.
Key electrical data for the UCC27524P
| Supply | 4.5 V to 18 V single supply, UVLO turns on near 4 V with 300 mV typical hysteresis |
| Drive | 5 A peak source and 5 A peak sink per channel, rail to rail output, two channels may be paralleled |
| Timing | 17 ns typical propagation delay, 6 ns rise and 10 ns fall, 1 ns typical delay matching between channels |
| Inputs | High 1.9 V to 2.3 V, low 1.0 V to 1.4 V, hysteresis 0.7 V to 1.1 V, minus 5 V continuous on the input pins |
| Quiescent | 300 microamps typical and 450 microamps maximum supply current with the inputs at 3.3 V |
| Temperature | Junction range minus 40 C to 150 C, thermal pad on the HVSSOP and WSON members |
Package, marking and reel data
| Body | P, PDIP 8 pin, 50 pieces per tube, lead finish NIPDAU at moisture level 1 unlimited floor life |
| Marking | 27524 on the top of the package, pinout industry standard with ENA, INA, GND, INB on one side |
| Siblings | D SOIC 8 and DGN HVSSOP 8 at 2500 per reel, DSD WSON 8 at 3000 per reel |
| Grade | The reel rows are published at minus 40 C to 140 C and the tube rows at minus 40 C to 150 C in places |
Where a through hole driver still earns its place
A PDIP body is not a legacy leftover on this part. Repair lines, test fixtures and small runs of industrial controllers still use through hole assembly, and a 50 piece tube suits a build of forty boards far better than a 2500 piece reel does. The 5 A drive also means the part can charge a 100 nC gate to 10 V in roughly 200 ns, so a pair of TO-220 MOSFETs in a 50 kHz converter switches cleanly without a buffer stage. Where the board is surface mount, the same silicon sits in the DGN and DSD bodies, and our pin to pin cross reference page lists the body options that share this pinout.
Two channels in parallel double the drive current, which the vendor supports directly. The two outputs must be joined at the pin, not at the gate, and the gate resistor is halved rather than removed. The other common use is a half bridge built from two discrete N-channel switches driven by the two channels of one device, with the enable pins used as a fast shutdown path. Because the enable pins are pulled up internally, a fault signal has to sink current to ground to disable the channel, which is the polarity a comparator with an open drain output provides.
Buyer questions on the UCC27524P
Does the part need a negative bias supply to handle negative input swings? No. The input pins tolerate minus 5 V directly, so a gate transformer that rings below ground does not need a clamp diode pair on the input. The outputs are a separate matter and follow the VDD rail.
Can the two channels drive one large MOSFET? Yes. The vendor states that paralleling the outputs increases the drive current, and the 1 ns matching keeps the two halves from fighting. Join the outputs at the package pins and keep the gate loop short.
Is a PDIP part still active? The addendum lists UCC27524P as active in production at 50 pieces per tube, with a .B row of the same body. The surface mount bodies carry the same silicon, so a later move to reflow does not change the electrical behaviour.
Availability and cross reference
The tube is the published packing for this body and the reel rows belong to the D, DGN and DSD packages, so a customer who needs 2500 pieces at once is buying a different package rather than a different part. Where the catalogue code carries a P and the customer expects a reel, the order has to be checked before a schedule is promised. We hold both the tube and the reel bodies and flag the packing on every quote, and the shortage route for this family is set out on our BOM shortage recovery page.