UCC21540DWKR
Product Specifications
UCC21540DWKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC21540DWKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC21540DWKR: the 14 pin body exists for 3.3 mm of channel to channel spacing
The UCC21540DWKR is a reinforced isolation dual channel gate driver in the DWK body, a 14 pin SOIC with 3.3 mm of minimum spacing between the two output channels. That spacing is the entire reason the package exists. The DW SOIC-16 version is pin compatible with the earlier UCC21520 and suits a half bridge where the two channels share a reference plane, while the DWK part puts enough distance between the channels that a bridge with a higher bus voltage can use it without an extra creepage barrier. Both are rated 5.7 kVRMS for one minute per UL 1577 and 8000 VPK reinforced per DIN EN IEC 60747-17.
The drive is 4 A source and 6 A sink, the propagation delay is 33 ns typical with 6 ns maximum pulse width distortion and a 10 microsecond maximum VDD power-up delay, and the common mode transient immunity is above 125 volts per nanosecond. Dead time is set by a resistor, the DIS pin shuts both outputs, and the input pins tolerate minus 5 V spikes for 50 ns, which is the detail that separates a driver that survives a noisy ground from one that latches.
Key electrical data for the UCC21540DWKR
| Drive | 4 A peak source and 6 A sink, up to 18 V VDD, 5 V and 8 V UVLO options |
| Timing | 33 ns typical propagation delay, 6 ns maximum pulse width distortion, 10 microseconds VDD power-up delay |
| Isolation | 5.7 kVRMS for one minute per UL 1577, 8000 VPK reinforced per DIN EN IEC 60747-17, CQC per GB4943.1-2022 |
| Immunity | Common mode transient immunity above 125 V per nanosecond, minus 5 V for 50 ns on the inputs |
| Supplies | VCCI UVLO rises at 2.7 V typical and falls at 2.5 V, quiescent 1.5 mA on the input side and 1.0 mA per output side |
| Grade | Junction -40 C to 125 C on the published rows |
Package, marking and reel data
| Body | DWK, 14 pin SOIC, 3.3 mm minimum channel to channel spacing, pin compatible option in DW SOIC-16 |
| Reel | 2000 pieces on a large reel for the DWK and DW bodies |
| Finish | NIPDAU, level 2 at 260 C, one year floor life on the A row |
| Status | The plain UCC21540DWKR row is marked Obsolete, the .A row is active and in production |
Spacing, creepage and the bus voltage
Reinforced isolation at 8000 VPK is a package claim as much as a silicon one: the barrier has to hold the voltage and the package has to keep the creepage distance across the surface. In the DWK body the 3.3 mm channel to channel spacing allows a higher working voltage between the two output sides than the DW body, and that is what lets one part drive both switches of a bridge on a bus that would otherwise need two separate drivers with separate barriers.
The practical constraint is the board. The 3.3 mm spacing has to be preserved on the copper, so no plane, no via and no solder mask opening can bridge the gap under the package. A poured ground plane on the top layer that runs under the body defeats the spacing the package was bought for. The second constraint is the VDD power-up delay of 10 microseconds: a controller that enables the bridge before the driver rails are valid will see both outputs low for that window, which is the intended behaviour rather than a fault. Our power management cross reference page lists the isolated driver codes we keep against this family.
Buyer questions on the UCC21540DWKR
Is this the obsolete row? The plain UCC21540DWKR row is marked Obsolete in the vendor addendum. The .A row of the same body is active, ships 2000 pieces per reel and carries the published plating and moisture data, so a new build should be quoted on that row.
What is the difference between the DW and DWK bodies? The DW is a 16 pin SOIC that is pin compatible with the earlier UCC21520, and the DWK is a 14 pin SOIC with 3.3 mm channel to channel spacing. The silicon is the same family; the spacing and the pin count are the difference.
Can the driver run from a 5 V rail on the output side? It can, with the 5 V UVLO option, but a 5 V rail limits the gate drive for a standard MOSFET and is usually reserved for logic level devices. A 12 V or 15 V rail is the normal choice for IGBT and silicon carbide.
Availability and cross reference
Because the plain row is obsolete, the only sane purchase path is the .A row, and a broker offer that names the plain code has to be checked against the date code and the plating record. We quote the .A row by default and flag the status difference on the quotation, which is the control that stops a customer from building a new product around a listing that the vendor has already closed. Our obsolete part cross reference hub page covers the alternatives we hold for this driver class.