Contact Us

TPS61288RQQR

Brand: Texas Instruments
Texas Instruments TPS61288RQQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61288RQQR — Power Management & Signal Chain | Superb Automation

TPS61288RQQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61288RQQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61288RQQR: an 18 V, 15 A synchronous boost converter in an 11 pin QFN

TPS61288RQQR is a 2.0 V to 18 V synchronous boost converter in a VQFN-HR (RQQ) body of 11 pins. The RQQ body is 2.5 mm by 3.0 mm with 11 pins, 3000 pieces on a large reel and the marking 61288. The HotRod package puts the pads on the underside of the lead frame, and the L version of the same part, marking 61288L, is the HotRod Lite variant the vendor recommends when the thermal margin is tight.

Order code and package

TPS61288RQQRVQFN-HR (RQQ), 11 pins, 3000 piece large reel, marking 61288, -40 to 125 C
TPS61288LRQQRHotRod Lite version, marking 61288L, same body and reel, recommended where thermal performance has to improve
Finish and floor lifeSn lead finish, MSL level 2 at 260 C with a one year floor life
Absolute maximum20 V on VIN, VOUT and SW, BST to SW plus 6 V, 6 V on the other pins
Junction range-40 C to 150 C junction, with the electrical tables taken from -40 to 125 C

Electrical parameters that decide the application

Input and output2.0 V to 18 V in with 2.4 V needed to start, 4.5 V to 18 V out
Switch current15 A peak switch current limit
Switching devices6.5 mOhm low side and 8.5 mOhm rectifier switch, both integrated
Switching frequency500 kHz in pulse width modulation, dropping into pulse frequency modulation at light load and low duty cycle
Efficiency94.7 percent at 3.6 V in, 13 V out and 2 A, 96.9 percent at 7.2 V in, 16 V out and 2.5 A
Quiescent current110 uA typical into the VOUT pin, 3 uA typical and 10 uA maximum into VIN with no switching
Input current ceiling2.1 A maximum into the VIN pin, which is the number that limits how much power can be pulled from a single cell
Startup2.3 V to 2.4 V undervoltage lockout rising, 1.8 V to 2.0 V falling with 400 mV of hysteresis, so a sagging cell can restart the converter
Protection19 V output overvoltage, cycle by cycle overcurrent and thermal shutdown
Internal railVCC regulated to 4.8 V with a 2 V falling threshold
ModulationSOO modulation on top of peak current control, which keeps regulation accuracy across load and input without losing efficiency
Shutdown2 uA typical into VIN with EN low and SW at 0 V

Family variants and how they differ

TPS61288LHotRod Lite variant, same ratings, chosen where the standard HotRod footprint does not give enough copper for the heat
Against a controller plus external FETsone 11 pin part replaces the controller, the gate drive and two switches, which is the reason it turns up in portable systems with a thin board
Current ceiling against inputthe 15 A switch limit is not the same as the input current, the 2.1 A VIN pin ceiling decides the power available from a single cell

Points to check before this part goes on a BOM

The 15 A switch current is the headline, and the 2.1 A input pin ceiling is the number that actually sizes the application. Boosting 3.6 V to 13 V at 2 A means roughly 26 W at the output, which at an efficiency in the mid nineties pulls over 7 A from the battery, well past what the VIN pin is rated for. The high efficiency figures in the table are quoted at 2 A and 2.5 A of output for exactly this reason: the switch limit is generous, the input path is not.

The 2.4 V startup threshold against a 2.0 V operating floor is the detail that decides whether a single cell board restarts after a deep discharge. The converter needs 2.4 V to come up, then holds down to 1.8 V to 2.0 V before the lockout falls, so a cell that sags under load does not drop the rail the moment the load steps.

Two efficiency points are published and both matter. 94.7 percent at 3.6 V in and 13 V out is the single cell boost case, 96.9 percent at 7.2 V in and 16 V out is a two cell or adapter fed case. A product quoted against the second number but built for the first will not meet its thermal budget, so the input voltage on the actual board has to be matched to the right row.

The 19 V output overvoltage protection sits close to the 18 V output ceiling, only 1 V of headroom, so a load that can regenerate into the rail needs its own clamp. The cycle by cycle overcurrent and the thermal shutdown cover the switch, not the output capacitor bank.

Getting the heat out of an 11 pin body

The 2.5 mm by 3.0 mm QFN puts 15 A of switch current into a body smaller than the inductor it usually sits next to, so the copper under the part is part of the specification rather than a mechanical detail. Both the standard HotRod and the HotRod Lite versions rely on the exposed pad and the vias beneath it, and the vendor recommends the Lite variant when thermal performance has to improve on a fixed board outline.

The MSL 2 rating is the second practical item. The part ships at 260 C with a one year floor life, so a reel that has been open on a shelf longer than that goes through the bake stated on the label before it is run. Both variants share the same reel count, 3000 pieces, and are told apart by the marking, 61288 against 61288L.

One more number belongs in the quote conversation. The 15 A switch limit and the 2.1 A input ceiling are both stated on the same page, and a buyer reading only the first will expect three times the output power the part can actually deliver from a single cell. Sizing the application against the input ceiling keeps the promise the page makes.

Where this order code fits

It is used for single cell and two cell lithium boost rails, power banks, portable audio and any handheld product that has to hold 12 V or 15 V from a battery that starts under 4 V. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Do the two package variants differ electrically? No. TPS61288RQQR and TPS61288LRQQR share the ratings and the 11 pin body, and the L part is the HotRod Lite version the vendor recommends when thermal performance has to improve. They are told apart by the marking, 61288 against 61288L.

Why is the input current limited to 2.1 A? Because the VIN pin and the internal path are rated for that, whatever the 15 A switch limit says. Input power is capped there, so the practical output power at a given boost ratio follows from it rather than from the switch current.

Does it start from a 2 V cell? It needs 2.4 V to start and will then run down to about 1.8 V before the lockout falls, with 400 mV of hysteresis. A cell resting at 2.0 V will not bring the converter up on its own.

What protects the output if the load regenerates? The 19 V overvoltage threshold is the only output side guard and it sits 1 V above the 18 V output ceiling, so a regenerating load needs an external clamp. The overcurrent and thermal shutdown protect the switch.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.