Contact Us

TPS61289RZPR

Brand: Texas Instruments
Texas Instruments TPS61289RZPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61289RZPR — Power Management & Signal Chain | Superb Automation

TPS61289RZPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61289RZPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61289RZPR a 20 A bidirectional buck boost with a mode pin

The TPS61289RZPR is a synchronous bidirectional converter in a 14 pin VQFN-HR body measuring 2.5 mm by 3.0 mm, with a low side range of 0.5 V to 23 V and a high side range of 4.5 V to 25 V. It integrates the high side rectifier FET at 8.5 milliohm and drives an external low side FET, and a MODE pin selects whether the power flows from the high side to the low side as a buck or from the low side to the high side as a boost.

The switching current is 20 A, and the current limit is programmable from 5 A to 20 A with a resistor from the ILIM pin to ground: 20 kilohm gives a 17 A to 20 A window. The conversion is forced PWM, so the ripple is predictable in both directions, and the switching frequency is 250 kHz while the low side is above 1.7 V, folding to 100 kHz below 1.5 V and 50 kHz below 0.5 V.

That frequency fold is the mechanism that allows a 0.5 V low side rail. A fixed 250 kHz solution would need an on time shorter than the minimum the gate driver can produce, so the part stretches the period instead. The 200 mV of hysteresis on the fold prevents the frequency from toggling at the boundary.

Key parameters from the SLVSGT4A document

High side range4.5 V to 25 V, with overvoltage protection at 26 V to 27 V and undervoltage at 3.1 V
Low side range0.5 V to 23 V, with the minimum set by the conversion ratio and the frequency
Current20 A switching, current limit programmable from 5 A to 20 A with an external resistor
Frequency250 kHz above 1.7 V low side, 100 kHz below 1.5 V, 50 kHz below 0.5 V, with 200 mV hysteresis
Reference0.985 V to 1.015 V at the feedback pin in PWM mode
Switch8.5 milliohm integrated high side rectifier, external low side FET
CompensationExternal network on the COMP pin, sink and source current 20 microamp
ProtectionCycle by cycle current limit, high side overvoltage and undervoltage, thermal shutdown at 160 degrees
Package14 pin VQFN-HR, 2.5 mm by 3.0 mm, RZP body, 3000 pieces on a large reel, moisture level 2

Two directions on one inductor

A bidirectional converter is used where the same rail has to charge and discharge, which is the case in a battery to bus converter in a portable product and in a supercapacitor buffer. The mode pin sets the direction of the power stage, but the current limit and the loop compensation are shared, so a board that has to work in both directions has to be stable at the worst of the two operating points rather than at the nominal one.

The external low side FET is the reason the current can reach 20 A in a 2.5 mm by 3 mm body. The heat of the low side conduction goes into a discrete part chosen for the board rather than into the package, and the integrated high side at 8.5 milliohm handles the rectification. Choosing that FET is the main thermal decision in the circuit.

The boost mode current limit is a valley limit and the buck mode limit is a peak limit, both set by the same resistor. That means the two directions do not have the same margin against a given load, and the resistor has to be chosen for the direction that runs closest to its limit.

Where this part fits

Battery to bus converters, supercapacitor buffers, USB power delivery front ends and any board where power has to flow both ways through one inductor. Our desk keeps the cross reference for wide range bidirectional parts, see power management cross reference and one stop BOM sourcing.

What to check before a purchase order

The RZP body is 14 pins on 2.5 mm by 3.0 mm with an exposed pad, and the thermal path runs through that pad into the board. Moisture level 2 with a one year floor life applies, so the reel needs dry storage. The ILIM resistor value has to be confirmed against the direction that runs closest to the limit, since 20 kilohm gives 17 A to 20 A in both modes but the two modes compare different currents.

The BOOT capacitor is specified between 0.1 microfarad and 1 microfarad with a 5.6 V Zener across it, and that Zener is not optional. A board that omits it will work until the first fast transient, then lose the high side gate drive. See incoming inspection plan for the receipt check on a 14 pin body.

Questions that come up on this part

Can the mode pin be switched while the converter is running, is the first question, and the answer from the pin description is that it must not be floating and it is a mode selection rather than a dynamic control. A board that has to reverse the power flow at runtime should use the enable and a defined sequence rather than toggling the mode. The second question is whether the part can regulate down to 0.5 V from 12 V. It can, at a reduced frequency, and the current available falls with the ratio.

The third question is about the 0.985 V to 1.015 V reference. With a 1 V reference the divider ratios are simple, but the tolerance is 3 per cent, so a rail that has to hold 2 per cent needs a trimmed divider or a different reference.