Contact Us

TPS563219DDFR

Brand: Texas Instruments
Texas Instruments TPS563219DDFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS563219DDFR — Power Management & Signal Chain | Superb Automation

TPS563219DDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS563219DDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS563219DDFR 3 A buck that stays in continuous conduction at every load

The TPS563219DDFR is a 4.5 V to 17 V, 3 A synchronous buck in an 8 pin SOT-23, 1.6 mm by 2.9 mm, with 68 milliohm high side and 39 milliohm low side FETs and a fixed 650 kHz switching frequency. Control is D-CAP2 with no external compensation, the reference is 1 per cent at 25 degrees, and the output range runs from 0.76 V to 7 V.

The defining behaviour is at light load: this part never leaves continuous conduction. Where the TPS563210A in the same body skips pulses to save standby current, this one keeps the inductor current flowing and holds a steady ripple down to no load. On a rail that feeds an analog section or a clock generator, that is the property that keeps switching noise out of the signal band, and it is why the two siblings exist rather than one part with a mode pin.

The rest of the pin set is shared: adjustable soft start through a capacitor, an open drain power good output, prebiased startup, cycle by cycle overcurrent limit, hiccup on sustained undervoltage, and non latching overvoltage, UVLO and thermal shutdown. Shutdown current is below 10 microamp, and the part is specified from 40 to 85 degrees ambient.

Key parameters from the SLVSDT2 document

Input range4.5 V to 17 V
Output current3 A with 68 milliohm high side and 39 milliohm low side FETs, against 133 and 80 on the 2 A member
Output voltage0.76 V to 7 V
Switching frequency650 kHz fixed
Reference accuracy1 per cent feedback voltage accuracy at 25 degrees
Light loadContinuous conduction at all loads, with the output ripple staying at a fixed amplitude
Shutdown currentBelow 10 microamp with the enable pin low
Package8 pin SOT-23, 1.6 mm by 2.9 mm, DDF body, ambient range 40 to 85 degrees

Ripple at no load, and why anyone cares

A pulse skipping converter at no load delivers a burst of pulses, waits for the output to sag, then bursts again. The output ripple in that state has a low frequency component set by the skip ratio, and it appears as a tone at a few kilohertz. In an audio product that tone is audible. In an instrumentation front end it sits inside the measurement band. Continuous conduction removes the tone and leaves a 650 kHz ripple that a small LC filter handles easily.

The trade is quiescent current, which is several milliamps rather than tens of microamps. A board on a permanent mains supply does not care and should take this part. A board on a battery should take the sibling.

Two parts, one pad, one decision

Because this device and the Advanced Eco mode sibling share a body and a pinout, the choice can be made late, after the first noise measurement. That is useful on a program where the analog section is added in a later revision. The risk is the same as with any shared body: a distributor splitting a family can put the wrong sibling on a reel, and the board will still work, which is the worst kind of wrong.

The marking is short on an 8 pin SOT-23, so the reel label is the practical check. On a first order of either sibling, ask for the label rather than trusting the carton, and record the carrier tape width on the incoming sheet so a later reel can be compared against the first one.

Where this part fits

Analog front ends, clock and reference rails, instrumentation, audio products and any 3 A rail where light load noise matters more than standby current. Our desk keeps the sibling comparison and the second source checks, see power management cross reference and how to verify a drop in replacement.

What to check before a purchase order

The DDF suffix is the 8 pin 1.6 by 2.9 mm SOT-23. The order code ends in 219 for this part and 210 for the pulse skipping sibling, and one digit is all that separates them on a label. Confirm the ambient inside the enclosure, since the part is specified to 85 degrees ambient and a sealed box can exceed that while the room stays comfortable.

See incoming inspection plan for the receipt check, and date code management for how we segregate siblings that share a carton.

Questions that come up on this part

Does continuous conduction mean the part cannot be shut down, is a common misreading. No, the enable pin still stops it, and shutdown current stays below 10 microamp. The second question is whether the 2 A member can cover a 3 A load at low ambient. It cannot; the FET resistances are nearly double and the current limit is set for the smaller die.