TPS563200DDCR
Product Specifications
TPS563200DDCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS563200DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS563200DDCR: 3 A synchronous buck, 4.5 V to 17 V input, 650 kHz, Eco-mode, SOT-23-6
TPS563200DDCR is a 3 A synchronous step down converter with both switches inside a six pin SOT-23 body, running at a fixed 650 kHz from a 4.5 V to 17 V input in a SOT-23-6 body of 6 pins. The switches measure 68 milliohm on the high side and 39 milliohm on the low side at 25 degrees. Control is D-CAP2, so there is no compensation pin and no external network, and the feedback threshold is 772 mV at 25 degrees with one per cent accuracy. Shutdown current is under 10 microamp, soft start is fixed at 1 ms, and the part starts into a prebiased output without pulling the rail down.
Order code and package
| TPS563200DDCR | Active, SOT-23-THIN (DDC) body, 6 pins, 3000 pieces on a large reel, marking 320 |
| TPS563200DDCT | Active, the same body with 250 pieces on a small reel |
| TPS562200DDCR | the 2 A member with 122 and 72 milliohm switches, same body and same pin out |
| Temperature range | minus 40 to 85 degrees ambient, narrower than the 125 degree members of the broader family |
| Pin count | six pins, no power good and no external soft start capacitor |
Electrical parameters that decide the application
| Input voltage | 4.5 V to 17 V |
| Output voltage | 0.76 V to 7 V, set by a divider into the VFB pin |
| Output current | 3 A continuous |
| Switch resistance | 68 milliohm high side, 39 milliohm low side at 25 degrees |
| Switching frequency | 650 kHz fixed |
| Feedback threshold | 772 mV at 25 degrees, one per cent accuracy at that point |
| Shutdown and quiescent current | under 10 microamp in shutdown, 190 to 290 microamp not switching |
| Current limit | 3.5 A minimum, 4.2 A typical, 5.3 A maximum |
Family variants and how they differ
| TPS563200 | 3 A, the string on this page |
| TPS562200 | 2 A with 122 and 72 milliohm switches and a 2.5 to 4.3 A current limit |
| TPS563210 | the eight pin member that adds a power good output |
| Soft start | 1 ms fixed internally, no capacitor to fit |
| Protection | cycle by cycle current limit, hiccup on a persistent fault, non latching overvoltage and undervoltage lockout, thermal shutdown |
Points to check before this part goes on a BOM
This is the six pin member, and the missing pin is the power good output. A board that needs to tell a sequencer the rail is valid has to use the eight pin member of the family. A board that only needs the rail does not pay for the extra pin, which is why this string is still the volume part in the family after the eight pin version was released.
Seventy two milliohms on the low side of the 2 A member is a real difference. The two strings are drop in on the same footprint and differ in current rating and resistance. A 3 A rail that turns out to need less current can move to the 2 A string and save cost, but the current limit also drops, and a load with a large inrush may then trip a part that previously started.
Four and a half volts input excludes a 3.3 V bus and leaves no margin on a 5 V bus. A 5 V rail at minus 10 per cent is exactly 4.5 V, so the converter is at its floor and any further dip puts it out of regulation. A 12 V adapter is the intended source and a 9 V supply works. A 24 V bus is above the 17 V ceiling and a vehicle rail is far above it.
One per cent at 25 degrees is a room temperature number. The feedback threshold is printed at 772 mV for 25 degrees, and the part is specified over minus 40 to 85 degrees ambient. A rail that has to hold its value in a hot enclosure needs the temperature coefficient of the divider added to the reference drift, and the divider resistors are usually the larger term.
Eco-mode changes the ripple at light load and nothing else. Above roughly 200 mA the converter switches at 650 kHz. Below that it skips pulses and the ripple becomes a low frequency wave with a larger amplitude. A digital rail does not care. An analogue rail fed from this part can pick up the low frequency component, which is why the family has members that keep switching at all loads.
A 1 ms soft start into a large output capacitor looks like a current limit event. The ramp is short and fixed, so a 470 microfarad bank draws the full current limit at power up and the output arrives in a staircase rather than a ramp. Keeping the output capacitance inside the range in the application section avoids it, and a bank that is already on the board for another reason has to be accounted for.
The 650 kHz frequency is a compromise between size and loss. It allows a 1.5 to 2.2 microhenry inductor, which is small enough for a dense board and large enough to keep the switching loss modest at 3 A. A board that fits a much smaller inductor to save height raises the ripple current and the loss, and a board that fits a much larger one slows the transient response.
Hiccup protection makes a fault look like a pulsing supply. A persistent short drives the current limit, then the undervoltage protection, then a pause, and the cycle repeats at a low frequency. A technician measuring the output during a fault reads a few hundred millivolts that comes and goes, which looks like an unstable converter rather than a protected one.
The DDC body is 1.6 mm by 2.9 mm and has no thermal pad. Heat leaves through the six leads, so the copper under and around the part is the only thermal path. At 3 A from 12 V to 5 V the conduction loss is about 0.45 W, which is a real number for that footprint. A board with a pour and vias carries it and a board with narrow traces folds back at a load the part is rated for.
What to confirm before this part goes on a purchase order
State the input bus and the output voltage. The same string sits on a 12 V to 5 V rail and on a 12 V to 1.2 V rail with different passives, and a substitute cannot be checked without the bus voltage.
Say whether a power good signal is needed. This six pin body does not have one, and a board that needs it must use the eight pin member of the same family.
Where this order code fits
It makes a 3.3 V or 5 V rail at 3 A from a 12 V adapter in a set top box, a television or a network terminal, where the board needs the fewest possible external parts. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Is it pin compatible with the 2 A member? Yes. TPS562200 and TPS563200 share the six pin body, the pin out and the 650 kHz frequency, and differ in the switch resistance and the current limit. Swapping from one to the other changes the thermal margin and the trip point, not the footprint.
What sets the output voltage? A resistor divider from the output to the feedback pin, against a 772 mV reference at 25 degrees. The divider current should be at least a hundred times the feedback pin leakage so that the ratio holds, and the lower resistor is usually in the few kilohm range.
Does it have a power good output? No. The six pin body brings out only the switch node, the input, the feedback, the enable and the bootstrap capacitor. A rail that has to report its status needs the eight pin member of the family, which adds that pin without changing anything else.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.