Contact Us

LF353DR

Brand: Texas Instruments
Texas Instruments LF353DR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LF353DR — Power Management & Signal Chain | Superb Automation

LF353DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The LF353DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LF353DR: dual JFET-input operational amplifier with 3 MHz bandwidth in an 8-pin SOIC

LF353DR is a dual operational amplifier with junction field effect input transistors in a SOIC body of 8 pins. Fifty picoamps of input bias current and an input impedance of 10 to the twelfth ohms are the two numbers that keep this part in production decades after it was introduced. The unity gain bandwidth is 3 MHz and the slew rate is 13 volts per microsecond typical, 8 volts per microsecond minimum, from a supply current of 3.6 milliamps for both amplifiers.

Order code and package

Order codeLF353DR
Functiondual operational amplifier, JFET input
PackageSOIC, 8 pins, D body
Input bias current50 picoamps typical
Input impedance10 to the twelfth ohms typical
Unity gain bandwidth3 MHz typical
Slew rate13 volts per microsecond typical, 8 volts per microsecond minimum
Supply current3.6 milliamps typical for both amplifiers
Input noise current0.01 picoamps per root hertz typical
Input noise voltage18 nanovolts per root hertz at 1 kHz
Crosstalk120 decibels at 1 kHz
Temperature range0 to 70 C, commercial only
DatasheetSLOS012 revision C, March 2016

Electrical parameters that decide the application

Input stagejunction field effect transistors, no bias current cancellation network
Supplyplus and minus 15 V typical, with the range stated in the absolute maximum table
Outputshort circuit protected
Offsetinternally trimmed at wafer level
Temperature driftbias current doubles roughly every 10 C, a property of the JFET junction
Bias current at temperaturejunction reverse current, so it rises with die temperature
Package options in familythe LF353 is offered in 8-pin SOIC and PDIP
Grade optionsthe LF412 is the same family with tighter offset specifications

Points to check before this part goes on a BOM

The bias current of 50 picoamps is a number measured at 25 C. It is a junction reverse current, so it doubles about every 10 degrees of die temperature, and a board that runs the amplifier hot sees a bias current several times the data sheet typical long before the ambient reaches the limit.

The commercial temperature rating of 0 to 70 C is the fact most often missed when this code is ordered for an industrial board. The part is characterised for that range only, and a product that has to work at minus 40 C needs the wider temperature member of the family rather than this order code.

Three megahertz of unity gain bandwidth with a 13 volt per microsecond slew rate is a combination that suits active filters up to a few tens of kilohertz. A 100 kHz filter with gain needs more bandwidth than this, and the shortfall appears as a peak in the response rather than as an obvious failure.

The JFET input also means the input capacitance and the source impedance form a pole. A 10 megohm source with a few picofarads of input capacitance puts the corner low enough to matter at audio frequencies, which is why the copper around this part deserves the same attention as the part number.

Where this order code fits

High impedance sensor front ends, sample and hold circuits, active filters and integrators order this code because the JFET input does not load a high impedance source. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Obsolete RF Part Replacement page.

Questions buyers ask

Can it run from a single 5 V supply? The input common mode range and the output swing have to be checked against the single supply curve; the part is normally used on a plus and minus 15 V rail.

Why does the bias current matter more than the offset? On a high impedance source the bias current multiplied by the source resistance becomes a voltage error that can exceed the offset by orders of magnitude.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.