LM193DR
Product Specifications
LM193DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM193DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM193DR: two comparators in an eight pin body, and the grade that survives a cold soak
LM193DR is the military grade of the dual differential comparator, eight pins in the SOIC body, 2500 pieces on a 330 millimetre reel, guaranteed from minus 55 to plus 125 degrees. It is the two channel version of the same comparator core used in the quad part, with the same open collector output and the same input stage that reaches the negative rail.
Two channels in an eight pin body is a different board decision from four in a fourteen pin body. The eight pin part fits next to the connector it monitors, which shortens the sense trace and removes a long run of noise pickup, and it leaves the rest of the board free for the converter. A window detector built from two comparators is the classic use, and it is the reason this code stays in catalogues after fifty years.
The grade is what separates LM193DR from the LM293 and LM393 codes on the same silicon: minus 55 to plus 125, against minus 25 to plus 85 and zero to plus 70. That window is bought with a full range test at both ends, and it is the row to look at first when a board has to work in an unheated cabinet.
LM193DR as the vendor document publishes it
Figures are from the vendor document revision AH dated April 2025, at a 5 volt supply unless the row says otherwise. Maximum values unless the row is marked typical.
| Channels | 2, independent, one supply pin pair |
| Supply voltage | 2 to 36 volts, split rails to plus or minus 18 volts |
| Input offset voltage | 2 millivolts typical, 5 maximum at 25 degrees |
| Input offset voltage over temperature | 9 millivolts maximum, minus 55 to plus 125 degrees |
| Input offset current | 3 nanoamps typical, 25 maximum |
| Input offset current over temperature | 100 nanoamps maximum |
| Input bias current | 25 nanoamps typical, 100 maximum |
| Input bias current over temperature | 300 nanoamps maximum |
| Common mode range | 0 to supply minus 1.5 volts at 25 degrees |
| Common mode range over temperature | 0 to supply minus 2 volts |
| Differential input voltage | plus or minus 36 volts |
| Large signal gain | 50 volts per millivolt minimum, 200 typical |
| Output low voltage | 150 millivolts typical, 400 maximum at 4 milliamps |
| Output low voltage over temperature | 700 millivolts maximum |
| Output sink current | 6 milliamps minimum at 1.5 volts of saturation |
| Output leakage | 0.1 nanoamps at 5 volts, 1 microamp at 30 volts over temperature |
| Supply current, two comparators | 0.8 milliamps typical, 1 maximum at 5 volts |
| Supply current at 30 volts | 2.5 milliamps maximum over temperature |
| Response time | 1.3 microseconds with 5 millivolts of overdrive |
| Response time, logic step | 0.3 microseconds, full logic swing |
| Output | open collector, 20 milliamps absolute maximum |
| Operating temperature | minus 55 to plus 125 degrees |
| Package | 8 pins, SOIC body D |
| Carrier | 2500 pieces on a 330 millimetre reel |
The two channel window detector, and why the offset split matters
Two comparators make a window: one watches the upper limit with its input order reversed, the other watches the lower limit. Both outputs are open collector, so they wire together into a single wired or node that pulls low when the signal is outside the window, and a single pull up sets the logic level. That is the whole circuit, and it is why the eight pin dual outlives most of the parts around it.
The offset split decides how wide the window really is. At 5 millivolts maximum per comparator, a 100 millivolt window is a 100 millivolt window plus or minus 10 millivolts, which is 10 per cent at the ends of the temperature range. On a 1 volt window the same error is 1 per cent, so the dual is comfortable on supplies and uncomfortable on small signal levels unless the window is trimmed.
The two channels are independent apart from the supply pins, and the vendor does not publish a crosstalk figure because the channels do not share a signal path. A step on one input can still move the supply through the shared pin, so a 100 nanoamp supply transient couples into the other channel through the 1.5 volts of headroom at the top of the common mode range. A 100 nanoamp ceramic capacitor next to the package removes that path on a fast board.
Input current, divider values and the error nobody models
At 300 nanoamps of bias current over temperature, the divider that sets the threshold is part of the error budget. A 10 kilo ohm pair carries 3 millivolts, a 100 kilo ohm pair carries 30 millivolts, and a 1 megaohm pair carries 300 millivolts. The same numbers apply to the A grade and to the commercial grade, so the divider is the term that an engineer can actually fix without changing the part number.
The threshold also moves with the supply if the divider is referenced to the supply rather than to a reference. A 5 per cent supply change on a divider-referenced window moves the threshold by 5 per cent, which is fifty times the offset error at a 1 volt window. That is the reason most window detectors in industrial gear use a shunt reference for the divider, and the comparator then only has to be fast and cheap.
Response time and the pull up resistor
Response time is 1.3 microseconds with a 5 millivolt overdrive and 0.3 microseconds on a logic step, measured with a 5.1 kilo ohm pull up to 5 volts and 15 picofarads of load. The pull up sets the rise time: 5.1 kilo ohms into 15 picofarads is a 77 nanosecond time constant, which is small against the 1.3 microseconds, but a 100 kilo ohm pull up turns the same node into a 1.5 microsecond edge and the response time stops being the comparator figure at all.
The sink side is the stronger half of the output. Six milliamps minimum at 1.5 volts will drive a small relay coil through a transistor, an optocoupler directly, or a light emitting diode in series with a resistor, and the 20 milliamp absolute maximum output current is the limit that the wiring has to respect.
Where the dual military comparator belongs
It belongs in a supply supervisor with an upper and a lower limit, in a two point level detector on a tank, in a bidirectional current limit built from two shunts, and in any board that has exactly two thresholds and no room for a fourteen pin body. It also belongs in retrofit work, because the pinout has been stable since the original part and a socket or a footprint from a nineteen eighties board still takes the current code.
The part is a poor fit where the two thresholds are far apart in voltage, because the common mode window is shared, and where the threshold has to hold to better than a millivolt, because the A grade of the quad family is tighter than any grade of the dual. For those cases the sourcing question becomes which family member is available on the reel, and our power management cross reference page lists the dual and quad codes that share this pinout family.
Carrier, status and what to confirm before a production order
LM193DR is the tape and reel code, 2500 pieces on a 330 millimetre reel, 12.4 millimetre tape width, with a 6.4 millimetre pocket and 2.1 millimetres of depth. The addendum dated April 2025 also prints LM193DRG4 on the same reel, which is the same body with the green mould compound code.
Not every code in the family appears in the current addendum. When a specific suffix is missing, the safe reading is that the row is no longer published rather than that the part exists under another name, so a production order should be confirmed against stock and date code before the purchase order is released. Our component obsolescence management page covers the check list, and the date code management page covers what to record when the parts arrive.
Buying questions that come with this code
Is LM193DR pin compatible with LM393DR? Yes. Both are the eight pin SOIC dual with the same pin functions, and the difference is the guaranteed temperature window and the test coverage behind it.
Can the two outputs be tied together? Yes, because both are open collector. One pull up resistor serves the wired node, and the sink current of both channels adds rather than fights.
Does the part need a supply decoupling capacitor? It works without one, but the 1.5 volts of headroom at the top of the common mode range is the first thing a supply transient eats, so a 100 nanoamp ceramic part within a few millimetres of the package is cheap insurance on a board with a switching converter nearby.