ISO7421DR
Product Specifications
ISO7421DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7421DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7421DR: dual-channel digital isolator at 1 Mbps with 9 nanosecond propagation in an 8-pin SOIC
ISO7421DR is a low power two-channel digital isolator with one channel each way in a SOIC body of 8 pins. This is the slowest and lowest power member of the dual-channel line: 1 Mbps, 9 nanoseconds typical propagation delay, and 300 picoseconds of skew between channels. The pair of numbers is unusual because a 1 Mbps part normally trades speed for consumption, and this one keeps a fast propagation path while limiting the signaling rate.
Order code and package
| Order code | ISO7421DR |
| Function | low power dual-channel digital isolator |
| Package | SOIC, 8 pins, D body |
| Channels | two, one forward and one reverse |
| Signaling rate | 1 Mbps |
| Propagation delay | 9 nanoseconds typical |
| Skew | 300 picoseconds typical |
| Supply current | 1.5 milliamps per channel at 3.3 V, 1.1 milliamps on the 7420 arrangement |
| Transient immunity | 50 kV per microsecond typical |
| Isolation | 2500 V RMS for one minute per UL 1577 |
| Temperature range | minus 40 to plus 125 C on the M grade |
| Arrangement options | 7421 one each way, 7420 both forward |
Electrical parameters that decide the application
| Barrier | silicon dioxide |
| Input filter | none on this grade, the rate limit is in the signal path |
| Level translation | 3.3 V and 5 V on each side |
| Certifications | UL 1577, CSA notice 5A, IEC 60950-1, IEC 61010-1, CQC GB 4943.1 |
| Output | CMOS push pull |
| Supply | 3.3 V and 5 V |
| Channel count | two in this body |
| Default output | set by the input state at power up |
Points to check before this part goes on a BOM
Nine nanoseconds of propagation delay on a 1 Mbps part is far faster than the rate requires, and that is the point: the delay is short enough that a loop with a reply in it does not have to be timed around the isolator. The rate limit is what keeps the current down, not a slow output stage.
Three hundred picoseconds of skew between the two channels is small enough that a pair carrying a clock and a data line keeps its relationship across a 1 Mbps link. At that rate a bit is a microsecond, so the skew is a fraction of a percent of the bit and the sampling point does not move.
The current per channel is the number that sells this part into battery instruments. At 1.5 milliamps on 3.3 V a pair draws less than an optocoupler's LED at the same signaling rate, and there is no LED ageing to budget for over a ten year life.
The family splits into the 7420 with both channels forward and this 7421 with one each way. A board that needs two signals in one direction and none coming back should use the 7420, because the reverse channel in this body is wasted current in a battery product.
Where this order code fits
Isolated UART links, optocoupler replacements on enable and alarm lines, and battery powered instruments order this code because the current per channel is 1.5 milliamps at 3.3 V. Boards comparing it with a neighbouring part start from our Obsolete RF Part Replacement page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
Is 1 Mbps enough for an isolated UART? Yes for standard rates up to 921.6 kbps, with the 9 nanosecond delay leaving room for the reply timing.
Why does a slow part have such a fast delay? The rate limit is set by the input filtering and the output stage drive, while the barrier itself is the same fast path used by the higher grades.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.