LM211QD
Product Specifications
LM211QD
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM211QD from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM211QD: the automotive member of the strobed comparator family, minus 40 to plus 125
LM211QD is the single strobed comparator in the automotive qualification, eight pins in the SOIC body, tube carrier, guaranteed from minus 40 to plus 125 degrees. The die is the same one used by the industrial part. What changes is the qualification behind it, the temperature window, and the paperwork that a tier one supplier has to hand to its customer.
The temperature window is the reason most engineers arrive here. A comparator that sits in an engine bay or on a transmission housing sees more than 100 degrees at soak, and the industrial part stops at 85. The automotive part carries the extra 40 degrees of hot margin and the cold end that goes with it, which is why the same eight pin body appears in places where the base part would be outside its ratings.
The rest of this page is the electrical summary, the qualification path, and the practical items that decide whether the Q code or the enhanced product is the right route for a given programme.
LM211QD as the vendor document publishes it
Figures are from the LM111, LM211 and LM311 document revision K dated March 2017, at plus or minus 15 volts unless the row says otherwise. The Q grade is the same silicon tested over the wider window.
| Channels | 1 |
| Supply | 5 to 30 volts single, or plus or minus 15 volts split |
| Input offset voltage | 0.7 millivolts typical, 3 maximum at 25 degrees |
| Input offset voltage over temperature | 4 millivolts maximum |
| Input offset current | 4 nanoamps typical, 10 maximum |
| Input bias current | 75 nanoamps typical, 100 maximum |
| Common mode range | minus 14.5 to plus 13 volts on a plus or minus 15 supply |
| Large signal gain | 40 volts per millivolt minimum |
| Output low voltage | 0.75 volts typical, 1.5 maximum at 50 milliamps |
| Output leakage | 0.2 nanoamps at 25 degrees, 0.5 microamps over temperature |
| Supply current, positive rail | 5.1 milliamps typical, 6 maximum |
| Supply current, negative rail | 4.1 milliamps typical, 5 maximum |
| Response time, low to high | 115 nanoseconds |
| Response time, high to low | 165 nanoseconds |
| Output rating | 50 volts, 50 milliamps |
| Strobe | 3 to 5 milliamps, current driven |
| Offset balance | two pins, external potentiometer |
| Operating temperature | minus 40 to plus 125 degrees |
| Package | 8 pins, SOIC body D |
| Part marking | LM211Q |
| Carrier | tube, 75 pieces |
The qualification path behind the Q suffix
The Q suffix is the vendor's automotive qualification, aligned with AEC-Q100 and supported by a production part approval process. For a tier one supplier that means a qualification report, a control plan, a process failure mode document and a change notification route, all of which the programme's quality engineer will ask for before the first production order.
None of that changes the circuit. The part still sinks 50 milliamps, still responds in 165 nanoseconds, still runs from a single 5 volt supply or from plus and minus 15 volts. What changes is the evidence that it will keep doing so across the temperature window and across the life of the vehicle, and the evidence is what a qualification audit actually examines.
A programme that does not need the evidence is paying for paperwork it will not use. That is the honest argument for the enhanced product flow or the industrial part on a non automotive product, and it is the argument a cost engineer will make in the first technical review.
The hot end: 125 degrees and the three rows that move
At 125 degrees the leakage current on the output reaches its 0.5 microamp ceiling, the saturation voltage at 50 milliamps approaches 1.5 volts, and the supply current on the positive rail reaches 6 milliamps. All three are inside the published limits, but each one eats margin that a 25 degree calculation assumed.
The leakage row matters most on a wired or bus. An output that leaks half a microamp into a 100 kilo ohm pull up develops 50 millivolts, which is below any logic threshold, so the leakage does not break the bus. It does matter on a high impedance analogue node, where the same 50 millivolts is a real offset, and that is the case where the load resistor should be smaller rather than the part changed.
The saturation row matters on a relay driver. A coil that draws 40 milliamps dissipates 60 milliwatts in the output transistor at 1.5 volts, and the eight pin body has to get rid of it at 125 ambient. The thermal resistance of the body and the copper under it decide whether that is comfortable or marginal, and the calculation belongs in the technical review rather than in the bill of materials.
Cold start and the strobe pin
At minus 40 the offset stays inside 4 millivolts and the bias current falls, so a threshold detector is at its most accurate at the cold end. The risk at the cold end is the supply ramp rather than the comparator: a 5 volt rail that comes up slowly leaves the output undefined until the supply passes the internal operating point, and a pull up that is powered from a different rail can hold the output high while the comparator is still off.
The strobe pin needs 3 to 5 milliamps at any temperature, and the resistor that sets that current should be chosen at the cold end where the logic output is at its lowest. A 1 kilo ohm resistor from a 5 volt logic output passes 5 milliamps at room and about 4.6 milliamps at minus 40 with a typical driver, which stays inside the window. A 2.2 kilo ohm resistor sits at 2.3 milliamps at room and outside the window at the cold end.
Tube carrier and the reel row that follows
The Q grade is offered in the tube carrier and on the reel. The tube is 75 pieces, which suits a pilot build and a bench. The reel row for the G4 code is 2500 pieces on a 330 millimetre reel with a 12.4 millimetre tape width, a 6.4 millimetre pocket and 2.1 millimetres of depth, at moisture level 1 with a 260 degree peak and unlimited floor life.
| LM211QD | SOIC D, 8 pins | 75 pieces, tube | automotive grade, marking LM211Q |
| LM211QDR | SOIC D, 8 pins | 2500 pieces, 330 millimetre reel | the same grade on the reel |
| LM211QDRG4 | SOIC D, 8 pins | 2500 pieces, 330 millimetre reel | green mould compound code, printed as active in the September 2026 addendum |
| LM211D | SOIC D, 8 pins | 75 pieces, tube | industrial, minus 40 to plus 85 |
The G4 row is the one the current addendum prints as active, with the marking LM211Q and the minus 40 to plus 125 window. The plain QD and QDR rows are the same die and the same grade, and a production order should confirm which of them the supplier holds before the purchase order is released. Our supplier quality audit page covers the documents to request, and the incoming inspection plan page covers what to measure when the first reel arrives.
Where the automotive single comparator belongs
It belongs in a battery management board, a body control module, an LED driver with a fault comparator, a motor controller with a current limit, and any automotive node where a threshold has to be resolved in under a microsecond and the output has to drive a lamp, a relay or an optocoupler directly.
It is the wrong part where the threshold is very small and the offset has to be a few tens of microvolts, because the A grade of the quad family is tighter. It is also the wrong part where a push pull output is wanted, because the open collector needs a pull up and a level that the receiving gate may not accept without one.
Buying questions that come with this code
Is LM211QD the same die as LM211D? Yes, and the difference is the qualification and the temperature window, plus the marking that lets an inspector tell them apart.
Can the Q part be used on an industrial board? It can, and it costs more, so the honest answer is to use it only where the window or the paperwork is needed.
What belongs on the purchase order? The full code including the Q and the carrier suffix, the date code requirement, and the qualification documents the programme needs. A part number without the Q is a different grade that will pass a functional test and fail an audit.