Contact Us

TPS562212DRLR

Brand: Texas Instruments
Texas Instruments TPS562212DRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS562212DRLR — Power Management & Signal Chain | Superb Automation

TPS562212DRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS562212DRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS562212DRLR: 4.2 V to 18 V, 2 A synchronous buck with selectable light load mode

TPS562212DRLR is a synchronous buck converter with an emulated current mode loop, a mode pin and a power good output in a SOT-5X3 body of 8 pins. It covers 12 V and 15 V rails with a 0.6 V reference, and the mode pin trades a power good flag for a longer soft start or trades efficiency at light load for a tighter output ripple.

Order code and package

Order codeTPS562212DRLR, DRL package, 4000 pieces on a large reel
BodySOT-5X3, 2.1 mm by 1.6 mm, eight pins, no exposed pad
ControlAdvanced emulated current mode, fixed 1.2 MHz, internal loop compensation
Mode pinSelects Eco-mode or forced continuous, and power good or external soft start
Reference0.6 V, 0.594 V to 0.606 V at 25 C and 0.591 V to 0.609 V over the full range
Output range0.6 V to 7 V, set by two resistors

Electrical parameters that decide the application

Input range4.2 V to 18 V operating, 20 V absolute maximum
Output current2 A continuous, high side peak limit 3.05 A to 4.1 A, low side valley limit 1.9 A to 3.15 A
High side switch66 mOhm typical at 25 C, measured with 5 V of bootstrap
Low side switch33 mOhm typical at 25 C
Switching frequency1.2 MHz nominal, 1.1 MHz to 1.3 MHz across the range
Minimum on time45 ns, which sets the smallest duty cycle at 5.4 per cent
Quiescent current120 uA in Eco-mode, 450 uA in forced continuous, 3 uA to 10 uA shut down
Soft start1.5 ms to 2.6 ms internal, or set by a capacitor on the PG/SS pin
Enable1.05 V to 1.25 V rising with 0.93 uA to 1.5 uA of sourcing current, 2.4 uA to 3.81 uA of hysteresis
ProtectionPeak and valley current limit, output over and under voltage with hiccup, thermal shutdown

Family variants and how they differ

TPS5622072 A from 17 V in a six pin SOT563, forced continuous only, no power good and a 0.804 V reference
TPS5632013 A in a six pin SOT-23 with pulse skip and a 768 mV reference, a larger body with a different pin out
TPS56C21512 A from 17 V in an 18 pin QFN, for a load this part cannot reach
TPS621303 A from 17 V in a 16 pin QFN with DCS control, an alternative when the board has room for a bigger body
TPS62410two independent 800 mA outputs from 6 V, for a board that needs two rails rather than one larger one

Points to check before this part goes on a BOM

The mode pin decides two unrelated things at once, and that is the detail most often missed. In one setting the pin selects Eco-mode or forced continuous operation, and in the other it selects whether the eighth function is a power good output or an external soft start capacitor. A board that needs a start-up ramp longer than the internal 2 ms gives up the power good flag, and a board that sequences two rails from power good cannot also stretch the ramp. The pin state is read at start-up and latched.

The 45 ns minimum on time sets a hard floor on the conversion ratio. At 1.2 MHz that is 5.4 per cent duty, so an 18 V input cannot regulate below 0.97 V and a 12 V input cannot regulate below 0.65 V. The 0.6 V setting is therefore a 5 V or lower rail option in practice, and a 12 V to 0.6 V rail is 5 per cent duty, close enough to the floor that the loop spends part of each cycle in minimum on time and the ripple grows.

Eco-mode costs less than a tenth of the quiescent current of forced continuous, 120 uA against 450 uA, and it also lets the output ripple grow at light load because the part stops switching between bursts. Forced continuous keeps the ripple at the switching frequency, which matters when the rail feeds an analog block or a radio, and it is the right choice when the 330 uA difference is small against the rest of the board.

The current limit is specified as a low side valley, 1.9 A minimum, so the average load that trips it is the valley plus half the ripple. At 2 A with 0.6 A of ripple the valley is 1.7 A and the part is clear of the limit, but with 1.4 A of ripple, which a 1.5 uH inductor gives, the valley sits at 1.3 A and the margin widens rather than shrinks. The high side peak limit of 3.05 A minimum is the one that catches a hard short before the valley circuit reacts.

The enable pin sources current, roughly 1.2 uA before the threshold and 2.4 to 3.81 uA of hysteresis afterwards. That current is what allows a single resistor from the input to the pin to set an under voltage lockout, and it is also what makes a high impedance divider inaccurate. A 1 MOhm and 200 kOhm pair draws 10 uA at 12 V, so a 1.2 uA pin current moves the trip point by about twelve per cent, while a 100 kOhm and 22 kOhm pair moves it by a little over one per cent.

Protection is a full set rather than a single comparator. Over voltage trips at 112 per cent of the reference, under voltage at 62.5 per cent with 5 per cent of hysteresis, and both lead to hiccup: 108 us of wait, then six switching cycles of retry, so a persistent fault produces short bursts rather than a continuous current. Power good has its own window, 87 to 92 per cent on the way up and 107 to 112 per cent before it drops, with 112 us and 48 us of delay.

The eight pin body carries the same 2 A as the six pin part in the previous generation but with 66 mOhm and 33 mOhm switches instead of 140 mOhm and 84 mOhm. At 2 A from 12 V to 5 V the conduction loss is 0.11 W in the high side and 0.08 W in the low side, roughly a quarter of what the older body produces, which is the real reason the part exists and the reason a drop in replacement changes the thermal margin.

Start-up is monotonic into a pre-biased output and the internal ramp is between 1.5 ms and 2.6 ms depending on the part, so a build that relies on a specific ramp time has to add the external capacitor and give up power good. The part also holds off switching until the input passes the 3.8 V to 4.2 V under voltage lockout, with a 3.4 V to 3.8 V falling threshold, so a 5 V rail that sags during a load step will restart cleanly rather than chatter.

The output range stops at 7 V even though the input goes to 18 V, and the loop needs the output at least a volt below the input to regulate. A 12 V to 9 V rail is outside the range, and a 12 V to 7 V rail is inside the range but at 58 per cent duty so the part runs at minimum off time for part of the cycle. Anything above 7 V belongs on a controller with external switches rather than on this part.

Where this order code fits

It belongs on the 12 V or 15 V rail of a set top box, a display, a smart speaker or a surveillance camera, where one rail between 0.6 V and 7 V has to carry up to 2 A and the board wants power good for sequencing. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can the output be set to 0.6 V from 12 V? It is 5 per cent duty against a 5.4 per cent minimum on time, so the loop sits at the edge and the ripple grows. A 5 V input or a lower switching frequency part is the cleaner route for a 0.6 V rail.

Does it have a power good output? Only when the mode pin selects power good instead of the external soft start. The two functions share one pin and the choice is latched at start-up.

What is the standby current? 120 uA in Eco-mode and 450 uA in forced continuous, with 3 uA to 10 uA when the enable pin is low. The difference matters on a rail that stays alive in standby.

Is it a drop in replacement for the six pin part? No. The body is larger, the pin out is different and the reference moves from 0.804 V to 0.6 V, so the feedback divider has to be recalculated.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.