LTM4620AIY#PBF
Product Specifications
LTM4620AIY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM4620AIY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTM4620AIY#PBF: the dual 13 A module in the 5.01 mm BGA and the input voltage it gives up
What this order code is
LTM4620AIY#PBF is the LTM4620A power module in the 15 mm by 15 mm by 5.01 mm BGA, tape and reel. The module delivers dual 13 A outputs or a single 26 A output, contains the controller, the power field effect transistors, the inductors and the support components, runs from 4.5 V to 16 V of input, and sets each output between 0.6 V and 5.3 V with one resistor. Total DC output error is plus or minus 1.5 percent, and multiple modules share current in multiphase up to 100 A.
This is the member of the family that trades input range for current. The LTM4628 in the same footprint runs to 26.5 V but stops at 8 A per channel; the LTM4620A runs to 13 A per channel and stops at 16 V. The two are pin compatible, so the choice between them is a decision about the bus voltage, and it is usually made once and then forgotten until a 24 V backplane appears.
Parameters as published
| Item | Value |
|---|---|
| Output configuration | dual 13 A, or single 26 A |
| Input voltage range | 4.5 V to 16 V |
| Output voltage range | 0.6 V to 5.3 V per channel |
| Total DC output error | plus or minus 1.5 percent |
| Efficiency at 12 V to 1.2 V | 86 percent, against 83 percent for the LTM4620 |
| Multiphase sharing | up to 100 A across several modules |
| Remote sense | differential amplifier |
| Switching frequency | resistor set and synchronisable |
| Temperature readout | internal temperature monitor |
| Sequencing | soft start and tracking |
| Protection | overcurrent foldback, output overvoltage |
| Pin compatibility | LTM4628 dual 8 A and LTM4620 dual 13 A |
| Body | 15 mm by 15 mm by 5.01 mm BGA |
Numbers that decide the application
Thirteen amps at 1.2 V is 15.6 W of output, and at 86 percent efficiency the loss is 2.54 W per channel. A single 26 A output is 31.2 W and 5.08 W of loss in one 225 square millimetre body, which is 0.116 A per square millimetre and the number that decides whether the board needs airflow. From a 12 V input the 26 A output draws 3.02 A, so the input connector, the bulk capacitor and the trace width are sized by that current rather than by the output.
The 16 V input ceiling is the constraint that shows up on a 24 V bus. A 24 V rail at plus ten percent is 26.4 V, which is inside the LTM4628 range and outside this one, so a board that expects to reuse the footprint for a 24 V product cannot. Below 16 V the arithmetic is friendly: at 12 V the duty cycle for a 1.2 V output is 10 percent, and at a 500 kHz setting the on time is 200 ns, which is comfortably above the minimum.
Multiphase sharing to 100 A is done with several modules, and 100 A at 1.2 V is 120 W, so a four module array is a 20 W per module proposition with the heat spread across four bodies rather than concentrated in one. Total DC error of plus or minus 1.5 percent is 18 mV at 1.2 V and 80 mV at 5.3 V, which is tight enough for most digital rails and not tight enough for a converter reference. The pin compatibility with the LTM4628 is the practical feature: a board can be laid out with the higher current part and built with the lower one during a shortage, provided the input stays under 16 V.
Where it fits and where it does not
It fits a 12 V telecom or datacom card that needs 13 A per rail, a 26 A single rail for a processor, a 100 A multiphase array for an FPGA, and a board that has to be able to build with either this module or the LTM4628. It does not fit a 24 V bus, an output above 5.3 V, a load that needs better than 1.5 percent without a post regulator, or a stack height that cannot take a 5.01 mm body.
Supply and second source questions
The footprint is shared across three current ratings, so the substitution question is answerable by the board itself: check the input voltage and the output current, then check whether the part in the socket is the 8 A or the 13 A version. What cannot be substituted is a module from another family with a different pin map, because the external capacitor set and the compensation are part of the module. Modules with their input ranges and current ratings are compared on the power management cross reference page.
Sourcing notes and next step
We quote the BGA body, the 5.01 mm height and the 13 A rating explicitly and will ask for the input rail voltage, since 16 V is a hard ceiling on this code. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability. The wider power device list sits on the analog and mixed signal IC page.
Request Quote — In Stock, 100% New & Original, Full Warranty