Contact Us

TPS54519RTER

Brand: Texas Instruments
Texas Instruments TPS54519RTER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54519RTER — Power Management & Signal Chain | Superb Automation

TPS54519RTER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54519RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54519RTER: a 5 A synchronous step down converter in a 3 mm by 3 mm QFN that runs from a 3.3 V or 5 V rail

TPS54519RTER is a synchronous step down converter with two integrated 30 milliohm MOSFETs, a 0.6 V reference and a switching frequency that can be set anywhere from 200 kHz to 2 MHz in a WQFN (RTE) body of 16 pins. It delivers 5 A continuous, draws 350 microamp of supply current at no load, drops to 2 microamp in shutdown, and holds its power good output low until the output sits inside 93 to 107 per cent of the set point. The junction temperature range runs from minus 40 C to 140 C.

Order code and package

TPS54519RTERWQFN (RTE) body, 16 pins, 3.00 mm by 3.00 mm with the thermal pad, 3000 pieces on a large reel, nickel palladium gold finish, moisture level 1 at 260 C unlimited floor life, marking 54519
TPS54519RTETthe same body on a 250 piece small reel, the string a pilot build orders before the main release
Suffixed rowsthe addendum repeats both strings with .A and .B suffixes, and the packing, finish and moisture level have to be read on the row rather than assumed from the suffix
Temperatureminus 40 C to 140 C on every row, which is the junction range the electrical tables are written against
Thermal padthe RTE body carries an exposed pad that is the only path for the heat the two 30 milliohm FETs produce at 5 A
Marking54519 on every row, so a reel can be identified from the part marking alone when the label is unreadable

Electrical parameters that decide the application

Input voltage2.95 V to 6 V operating, which covers a 3.3 V rail with tolerance and a 5 V rail with the same margin
Output current5 A continuous from the two integrated switches, with the inductor and the output capacitor setting the ripple rather than the device
Switch resistance30 milliohm typical on both the high side and the low side FET, which is what keeps the efficiency curve flat at 5 A
Switching frequency200 kHz to 2 MHz set by a resistor on the RT pin, and an 84 kilohm resistor lands the typical part at 490 kHz to 600 kHz
Reference0.6 V with plus or minus 1 per cent initial accuracy, so the output divider sets the rail and the tolerance is fixed at the reference
Supply current350 microamp typical with no load, which is what makes the part usable on a rail that is always on
Shutdown current2 microamp when the enable pin pulls the device into shutdown mode
Undervoltage lockout2.6 V internally, and it can be raised by a resistor network on the enable pin when the rail must not start below a higher threshold
Power goodan open drain output that releases once the output is inside 93 to 107 per cent of nominal, which is the window a downstream sequencer checks
Soft startset by a capacitor on the SS/TR pin, and the same pin can be used to track the output to a second rail during power up
Current limitcycle by cycle on the high side switch, with frequency foldback and thermal shutdown behind it
Protection behavioursafe start up into a pre-biased output, so a rail that is already held up does not get discharged through the low side FET

Family variants and how they differ

RT pinone resistor sets the frequency, and the same pin accepts an external clock when several converters have to run in step
SS/TR pina capacitor sets the ramp and a divider makes the output track another rail, which is the difference between a sequenced and a tracking supply
EN pina divider on the enable pin raises the undervoltage lockout above the internal 2.6 V, which is how a 5 V rail is kept off until the input is really there
PWRGD pinopen drain, so it can be pulled to a rail other than the output and can be wired OR with a second converter
COMP pinthe compensation network sits outside, which lets the loop be tuned to the output capacitor rather than fixed inside the device

Points to check before this part goes on a BOM

The inductor is the part that decides the ripple. At 2 MHz the inductor can be small, but the switching loss rises and the efficiency at 5 A falls, so most boards settle between 500 kHz and 1 MHz rather than at the top of the range.

The thermal pad is not optional. At 5 A into a 3.00 mm body the pad and the vias under it carry most of the heat, and a board that leaves the pad unconnected will fold back or shut down well before the current limit is reached.

The enable divider is the cheapest undervoltage lockout available. A two resistor divider on the enable pin holds the converter off until the input reaches the chosen level, which matters on a 5 V rail that comes up slowly.

Pre-biased start up is handled internally. A rail that is already held up by another source will not be pulled down when the converter starts, which is what keeps a shared 1.8 V rail from glitching during a sequencing fault.

The moisture level is 1 at 260 C with unlimited floor life, so the reel does not need dry packing control on the line, unlike most parts in this body size.

What the 5 A rating means on a real board

The 5 A figure is the switch current the two FETs can carry at the junction temperature the tables are written for. On a board with a 3.3 V input, a 1.2 V output and a 1 MHz switching frequency, the losses split between conduction and switching, and the pad temperature is what sets the real ceiling.

At 5 V input the duty cycle is short and the switching loss dominates, so the same board runs cooler at 2 MHz only if the FETs are given room. Most applications run between 500 kHz and 1 MHz, where the inductor is still small and the efficiency stays above 90 per cent at full load.

Where this order code fits

The part suits a point of load rail for a DSP, an FPGA or a network processor, where a 3.3 V or 5 V bus has to come down to a core voltage at 5 A in a small area. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

What sets the output voltage? A divider from the output to the VSENSE pin against the internal 0.6 V reference. The reference is plus or minus 1 per cent, so the divider tolerance and the reference tolerance together set the rail accuracy.

Can it run from a 5 V rail with a 3.3 V output? Yes. The input range is 2.95 V to 6 V and the output is set by the divider, so a 3.3 V rail from a 5 V input sits well inside the duty cycle range at any frequency in the window.

What happens on an overload? The high side switch limits cycle by cycle, the frequency folds back to keep the inductor current under control, and thermal shutdown takes over if the junction keeps rising.

Is the packing the same on every row? No. The RTER string is 3000 pieces on a large reel and the RTET string is 250 on a small reel. Both are moisture level 1 at 260 C, but the reel size decides whether a line can run a pilot without re-reeling.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.