SN65LBC176QDR
Product Specifications
SN65LBC176QDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65LBC176QDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65LBC176QDR: the minus 55 C to 125 C member of the LBC176 bus transceiver family
The SN65LBC176QDR is a 5 V differential bus transceiver for multipoint links, and the Q in the string marks the extended temperature version: the published range is minus 55 C to 125 C, against minus 40 C to 85 C on the standard SN65LBC176. It meets TIA/EIA-485-A and ISO 8482:1987(E), it combines a three state differential driver with a differential input receiver in one 8 pin body, and the two halves share the bus pins so one pair of terminals carries both directions.
The receiver input sensitivity is plus or minus 200 mV maximum with 50 mV of typical hysteresis, which is what lets a small differential signal survive a long cable. The disabled supply current is 200 uA maximum, the driver limits current in both directions, and a thermal shutdown protects the die if a fault holds a driver on. The receiver is fail safe on an open circuit, so an unplugged cable reads as a defined level.
Key data for the SN65LBC176QDR
| Standard | TIA/EIA-485-A and ISO 8482:1987(E), bidirectional multipoint bus transmission |
| Temperature | Minus 55 C to 125 C on the Q member, which is the reason this row exists separately from the standard part |
| Receiver | Input sensitivity plus or minus 200 mV maximum, 50 mV typical hysteresis, open circuit fail safe |
| Driver | At least 1.5 V differential into a 54 ohm load, positive and negative current limiting, thermal shutdown |
| Power | Disabled supply current 200 uA maximum, low skew between channels, LinBiCMOS process for low consumption |
| Bus | Wide positive and negative common mode range, high impedance when disabled or unpowered |
Body, marking and reel data
| Body | D, SOIC 8 at 4.90 mm by 3.91 mm, shared with the standard temperature member |
| Reel | 2500 pieces on a large reel, carrier tape 12.0 mm, 330 mm reel |
| Marking | 7LB176 on the plain row, 75LBC176 on the .A row, so the two rows are told apart by the printed code |
| Moisture | The published row prints N/A for package type in the moisture column, so no level is declared and the reel should be treated as uncontrolled until the vendor confirms |
| Status | The tube row SN65LBC176QD prints Obsolete, the reel row QDR prints active and in production |
When the extended range is not optional
Most RS-485 parts stop at 85 C and a few reach 125 C. A minus 55 C bottom is unusual and it is what puts this row into equipment that starts in an unheated enclosure, on a mast, or in a vehicle that spends the night outdoors. The same die works at both ends of the range, but the published limits are what an acceptance test is written against, and a test at minus 55 C cannot be passed by a part whose datasheet stops at minus 40 C. Cold start is where the difference shows: a liquid crystal display and an electrolytic capacitor both behave differently at that temperature, and the transceiver is the part that has to keep the link alive while the rest of the board is still waking up.
The bus side behaves like the standard member, which is the point. Sensitivity, hysteresis, drive level and failsafe behaviour are the same, so a board that already carries the standard part can take the Q row without a change to the termination or the cable. The only difference a builder sees is the marking and the temperature column on the qualification report.
Questions we get when this code is on a BOM
The first question is whether the Q row and the standard row are interchangeable. Electrically they are, because the silicon and the pinout are the same, but a build that is qualified against minus 55 C must not be shipped with a part rated to 85 C, and the two print different markings so the mistake is visible if incoming inspection looks. We quote the Q row explicitly and do not allow a silent substitution.
The second question is about the moisture column. The vendor file prints N/A for package type on this row, which means no moisture level is declared for the shipping format. A line that receives the reel and has no bake rule needs to know that, and we say it on the offer rather than letting the receiving clerk invent a level from the family.
How SUPERB supports this line item
We supply the SN65LBC176QDR for extended temperature builds and we state the marking and the temperature band on the offer, because a substitution with the standard member would be invisible on the board. Customers comparing the two temperature rows can use our pin to pin cross reference page, which lists where the limits differ and where they do not.
For equipment that runs in an unheated enclosure, the incoming inspection plan page describes how we document the temperature band and the date code on every shipment so the qualification file stays closed.