Contact Us

SN65LBC184P

Brand: Texas Instruments
Texas Instruments SN65LBC184P is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65LBC184P — Power Management & Signal Chain | Superb Automation

SN65LBC184P

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65LBC184P from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65LBC184P: an RS-485 transceiver with the surge protection built in

The SN65LBC184P is a differential bus transceiver in the trade standard SN75176 footprint, with transient suppression integrated on the bus terminals. That integration is the whole point of the part: instead of adding a TVS diode array, a series resistor and a board arrangement that keeps the clamp close to the connector, the protection sits inside the eight pin body and the board keeps its original outline.

The published immunity figures are the reason engineers ask for this code by name. Bus terminals survive 30 kV contact discharge and 30 kV air gap discharge under IEC 61000-4-2, 15 kV under the human body model, and a 400 W peak surge per IEC 61000-4-5. The driver edge rate is controlled so that long cable stubs do not ring, which is what allows 250 kbps operation in an electrically noisy cabinet without a scope on every unit.

Key data for the SN65LBC184P

FunctionHalf duplex differential transceiver, one driver and one receiver on a shared pair
Immunity30 kV IEC 61000-4-2 contact and air gap, 15 kV HBM, 400 W peak per IEC 61000-4-5
Bus loadOne quarter unit load, which allows 128 devices on one segment
Speed250 kbps with controlled driver slew rate for long stubs and noisy environments
Supply5 V rail, disabled supply current 300 uA maximum
BehaviourOpen circuit failsafe receiver, thermal shutdown, power up and power down glitch protection

Body, marking and reel data

BodyPDIP P, 8 pins, 9.81 mm by 6.35 mm, the through hole body used on older control boards
Reel50 pieces in a tube, so this is a hand load or a tube feeder part rather than a reel part
Marking65LBC184 printed on the body
ThermalJunction to ambient 108.7 C per W in the P body against 116.3 C per W in the SOIC body
Temperature0 C to 70 C on this row, which is a commercial grade window

Where the integrated clamp changes the board

A utility meter or a motor drive that brings the bus pair straight to a screw terminal normally needs three extra parts per node and a keep out area for them. With this transceiver the pair goes to pins 6 and 7 and the protection is already inside. The result is a smaller node, fewer solder joints and one less part to place on a line that may run at a modest volume.

The controlled edge rate also solves a mechanical problem. Long stubs off a backbone cable behave like transmission line taps, and a fast driver rings at the tap. A slower edge turns the ring into a small bump that the receiver tolerates, which is why the part is specified at 250 kbps and not at 10 Mbps. Choosing it for a 1 Mbps bus would be a mistake, and a customer who needs the higher rate should look at the 3082E or the HVD72 family instead.

Practical questions before this row is ordered

The first is the temperature window. This row is 0 C to 70 C, and there is a separate industrial row in the same body. A cabinet that is specified to minus 20 C cannot use the commercial row even though the electricals look identical on a bench test.

The second is the packing. Fifty pieces in a tube means the line either has a tube feeder or the operator loads by hand, and a prototype run of twenty units will consume nearly half a tube. The third is the failsafe behaviour: the receiver output is defined for an open circuit, but a terminated bus with no active driver is a different condition, and bias resistors are still the usual answer.

How a surge protected node is quoted

This part is quoted with the body and the packing named explicitly, because the tube quantity and the commercial temperature window both decide how the line runs. A prototype that takes twenty pieces will consume part of a tube, and a production build needs either a tube feeder or an agreement to move to a reel part with the same die and a different finishing line.

For the customer who is protecting a field bus, we ask for the cable length, the number of nodes and the surge class before we confirm the code. A node count above 32 depends on the quarter unit load, and a surge class above the 400 W peak figure means the external clamp still has a job even with the integrated protection. Those two answers change the quote more often than the price of the part does.

For a node count above 32 the quarter unit load figure matters, and the full 128 node limit assumes the bias network and the termination are sized for it. Boards that are replacing an SN75176 socket usually keep the same footprint and only need the protection reviewed, which is covered in our drop in replacement checklist. Where the part is being bought for a long life product, the planning note sits on our LTB planning page.