SN65ALS176DR
Product Specifications
SN65ALS176DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65ALS176DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65ALS176DR: a 35 Mbaud RS-485 transceiver with a 15 ns skew limit
The SN65ALS176DR is a differential bus transceiver in an 8 pin SOIC that meets TIA/EIA-422B and TIA/EIA-485-A as well as the ITU V.11 and X.27 recommendations, and operates at data rates up to 35 Mbaud. It combines a three state differential driver and a differential input receiver on one 5 V supply, with the driver and receiver enables brought out separately so they can be tied together as a direction control.
The family is differentiated by skew: the SN65ALS176 is the 15 ns part, the SN75ALS176 is 10 ns, the A version 7.5 ns and the B version 5 ns. Skew is what limits the usable bus length at a given data rate, because the difference between the two lines of a pair turns into timing error at the receiver. At 35 Mbaud the bit period is 28 ns, so a 15 ns skew is half a bit and leaves no margin for cable; the tighter grades exist for the longer buses and the higher rates.
Key data for the SN65ALS176DR
| Standard | TIA/EIA-422B, TIA/EIA-485-A, ITU V.11 and X.27, which is the full multipoint bus specification |
| Data rate | Up to 35 Mbaud on a balanced line |
| Skew | 15 ns on the SN65ALS176, against 10 ns on the SN75ALS176, 7.5 ns on the A version and 5 ns on the B version |
| Supply current | 30 mA maximum on a single 5 V supply, which is low for a part that drives a 60 mA class bus |
| Protection | Thermal shutdown, driver positive and negative current limiting, receiver input hysteresis, glitch free power up and power down |
| Temperature | Minus 40 C to 85 C on the SN65 prefix, against 0 C to 70 C on the SN75 prefix |
Body, marking and reel data
| Body | D, 8 pin SOIC at 4.9 mm by 3.91 mm; a P, 8 pin PDIP at 9.81 mm by 6.35 mm is also published |
| Reel | R suffix is the large reel; the SOIC is the body used on automated assembly and the PDIP is for through hole prototyping |
| Pins | Driver inputs and outputs, receiver inputs and outputs, a driver enable and a receiver enable that can be tied for direction control |
| Bus port | The driver outputs and receiver inputs are connected internally to one bus port that presents minimum load when the driver is disabled or the supply is off |
| Document | SLLS040I dated August 1987 and revised January 2023, one of the oldest documents in the catalogue and still current |
Where an ALS transceiver still earns its place
A 35 Mbaud RS-485 bus is fast for the standard and is used in motion control, in encoders and in short haul links between racks. The SN65ALS176 is the workhorse of that generation: it is a 5 V part with a wide common mode range, a thermal shutdown and a fail safe receiver that reports a defined state when the bus is open, which is what keeps a node from reporting a random frame when the cable is unplugged.
The fail safe behaviour is worth understanding because it is often the reason a part is specified. A receiver with no fail safe outputs a random level when the differential input is near zero, and on an idle bus that becomes noise that the protocol layer has to filter. The SN65ALS176 receivers are specified to output a defined high when the input is open, which removes that source of errors and lets a protocol run without a timeout on an idle line.
The 30 mA supply current is low for a driver that can source the 60 mA that a terminated bus requires, and it is what allows a node to be powered from a small isolated supply such as the one a push pull driver provides. That combination, an isolated 5 V rail and an RS-485 transceiver, is the standard isolated port, and the two parts are usually specified together. Our CAN bus transceiver selection note covers the differential bus parts by standard, data rate and isolation, and the pin to pin cross reference covers the SOIC-8 bus transceiver footprint that several generations share.
Buyer questions on the SN65ALS176DR
Is this part 3.3 V compatible? No, it is a 5 V part. A 3.3 V bus needs a different family, and the logic interface thresholds of this part are set for 5 V logic.
What is the difference between the SN65 and SN75 prefixes? Temperature range. The SN65 is specified from minus 40 C to 85 C and the SN75 from 0 C to 70 C, with the same die otherwise.
Can the driver and receiver enables be tied together? Yes, that is the normal direction control: one signal drives both, so the node either transmits or listens. A bus that needs a listen while transmitting state, as some protocols do, has to drive them separately.
Availability and ordering notes
SN65ALS176DR is the 15 ns skew member in the 8 pin SOIC, on a large reel. The tighter skew grades are separate order codes in the same body, so a bus that fails at a long length can often be fixed by changing the grade rather than the board. The document dates from 1987 with a 2023 revision, which means the part is mature and the electrical rows have been stable for decades, and a quotation that shows a long lead time should be checked against the tighter grade rather than against an alternative family.