Contact Us

INA819IDRGR

Brand: Texas Instruments
Texas Instruments INA819IDRGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA819IDRGR — Power Management & Signal Chain | Superb Automation

INA819IDRGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA819IDRGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA819IDRGR: 35 uV offset and 8 nV per root hertz in a low power instrumentation amplifier

The INA819IDRGR is a precision instrumentation amplifier in an 8 pin WSON at 3 mm by 3 mm. It holds offset to 35 uV maximum with 10 uV typical, noise to 8 nV per root hertz, and supply current to 385 uA maximum, which is the combination that makes it usable in a battery instrument that also has to resolve a microvolt signal.

Gain is set from 1 to 10,000 by one external resistor, and the amplifier stays stable with a 1 nF capacitive load, which is unusual in this class and removes the series resistor that a cable driver would otherwise need. The inputs are protected to 60 V, so a sensor that is powered down while the amplifier is on, or a transducer that is hot plugged, does not destroy the front end. Common mode rejection is 110 dB minimum at a gain of 10 and power supply rejection is 110 dB minimum at unity gain.

Key data for the INA819IDRGR

Offset35 uV maximum and 10 uV typical, with 5 ppm per degree gain drift at unity gain and 35 ppm per degree above it
Noise8 nV per root hertz input voltage noise, which is the figure that sets the resolution floor for a low impedance source
Bandwidth2 MHz at a gain of 1 and 270 kHz at a gain of 100, stable with a 1 nF load
RejectionCommon mode rejection 110 dB minimum at a gain of 10, power supply rejection 110 dB minimum at unity gain
Input protectionInputs protected to 60 V, which is well above the 36 V maximum supply and covers an unpowered sensor
Supply4.5 V to 36 V single supply or 2.25 V to 18 V dual, 385 uA maximum supply current, minus 40 C to 125 C

Body, marking and reel data

BodyDRG, 8 pin WSON at 3.00 mm by 3.00 mm; the family also ships SOIC-8 at 4.90 mm by 3.91 mm and VSSOP-8 at 3 mm by 3 mm
ReelR suffix is the large reel; the WSON has no leads, so the inspection method is different from the SOIC
Gain resistorOne external resistor between the two RG pins sets any gain from 1 to 10,000, with the resistor tolerance dominating the gain error above 100
Input stageSuper beta transistors, which is where the low bias current and the low current noise come from rather than from a chopper
DocumentSBOS959D dated December 2018 and revised April 2022

Where a 35 uV offset with 8 nV of noise is the right point

The INA819 sits between the very low noise parts, which draw milliamps, and the micropower parts, which have microvolt noise. At 385 uA it can run from a battery for years, and at 8 nV per root hertz it can resolve a 10 uV signal in a 1 kHz bandwidth. That combination is what a portable instrument needs: a strain gauge bridge, a thermocouple with a cold junction, a flow sensor with a 2 mV full scale output.

The 60 V input protection is worth more than it looks. A bridge that is excited from a 10 V source and an amplifier that is powered from 3.3 V can see the excitation on its input during a fault, and a front end without protection needs external clamp diodes and a series resistor that adds noise. With the protection inside the part, the series resistor can be small enough that its noise contribution stays below the amplifier's own 8 nV.

The 1 nF stability is the detail that simplifies a cable connection. A shielded cable presents 100 pF or more, and many instrumentation amplifiers need a series resistor to stay stable into it, which forms a pole with the cable capacitance and slows the response. The INA819 does not, so a remote sensor can be connected through a cable without a compensation network. Our amplifier cross reference groups the instrumentation amplifiers by noise and supply current, and the medical device components note covers the same front end in diagnostic equipment, where the 60 V protection and the low bias current are the two rows that matter.

Buyer questions on the INA819IDRGR

Can it run from a single 5 V supply? Yes, the minimum single supply is 4.5 V, so 5 V works, and the output swings inside that rail. A 3.3 V system needs the INA823 instead.

What gain resistor gives 100 V/V? The value follows the gain equation in the document and is in the low kilo ohm range for a gain of 100; a 0.1 per cent resistor keeps the gain error below the amplifier's own contribution.

Is the WSON body harder to inspect? Yes, there are no leads to inspect, so the assembly has to rely on paste volume control and x ray. The SOIC body is the choice for a low volume build without x ray.

Availability and ordering notes

INA819IDRGR is the WSON-8 member of the family, and the same die is offered in SOIC-8 and VSSOP-8 as separate order codes. Because the three bodies have different footprints and different inspection needs, a substitution between them is a board change. The part is a 2018 release with a 2022 revision, so it is a mature line with a stable document rather than a new part whose packaging data is still settling.