Contact Us

SN65LBC172ADWR

Brand: Texas Instruments
Texas Instruments SN65LBC172ADWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65LBC172ADWR — Power Management & Signal Chain | Superb Automation

SN65LBC172ADWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65LBC172ADWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65LBC172ADWR: four RS-485 drivers at 30 Mbps in one 20 pin body

The SN65LBC172ADWR packs four differential line drivers into a 20 pin SOIC. Each driver is a three state output for TIA/EIA-485, TIA/EIA-422 and ISO 8482 applications, and the set carries signalling rates up to 30 Mbps with propagation delays below 11 ns. It is the driver half of a bus interface, so the receiver side comes from a separate part or from the controller.

The drivers include positive and negative current limiting and a thermal shutdown, they go high impedance when disabled or unpowered, and the standby supply current is 1.5 mA maximum. The output pins are protected to 12 kV human body model. The pinout is compatible with the SN75172, the AM26LS31, the DS96172, the LTC486 and the MAX3045, which is why this part turns up on backplanes and on boards that were laid out in the 1990s and are still in production.

Key data for the SN65LBC172ADWR

ChannelsFour differential drivers, each with a three state output and an enable
RateUp to 30 Mbps, propagation delay below 11 ns, published eye pattern at the full rate
OutputAt least 1.5 V differential into a 54 ohm load, common mode output between 2 V and 2.8 V
ProtectionOutput ESD 12 kV, positive and negative current limiting, thermal shutdown, power up and down glitch free
Power1.5 mA maximum standby supply current with all drivers disabled, high impedance when powered off
CompatibilityPin compatible with SN75172, AM26LS31, DS96172, LTC486 and MAX3045

Body, marking and reel data

BodyDW, SOIC 20, the wide body that carries four drivers and their enables
Reel2000 pieces on a large reel, carrier tape 12.4 mm, 330 mm reel
Marking65LBC172A on both published rows
Finish and moistureThe plain row prints Call TI in the moisture column, the .A row prints level 1 with unlimited floor life
TemperatureMinus 40 C to 85 C on the SN65 member, 0 C to 70 C on the SN75 member of the same die

Where four drivers in one body pay off

A backplane that carries several differential pairs needs one driver per pair, and four separate 8 pin packages cost board area and assembly steps. The 20 pin body puts them side by side with a shared ground and a shared supply, which also keeps the skew between channels low because the die is at one temperature. That skew figure is what makes the part usable for parallel data as well as for independent links.

The pin compatibility with older driver families is the second reason it is chosen. Boards that were laid out for an AM26LS31 or a DS96172 can be built today with a part that is still in production, and the electrical behaviour is close enough that the existing termination and cable work unchanged. That is a repair strategy rather than a new board, and it keeps installed equipment serviceable. The eye pattern published at 30 Mbps assumes a 54 ohm load and a short trace, so a backplane with long stubs needs the rate reduced even though the driver is rated higher. That trade is normal and it is cheaper than changing the connector.

Questions we get when this code is on a BOM

The first question is about the difference between this driver and a transceiver. A transceiver has a receiver inside and a direction pin, while this part only drives. A board that expects to read the bus back needs the receiver half, and a substitution in either direction will leave one function missing. We ask which side of the link the part sits on before quoting.

The second question is about the enable logic. Each driver has two enable inputs, one active high and one active low, which lets the same part be wired for either polarity. A board that ties one of them to a fixed level must be checked against the polarity the board assumes, because a floating enable on a high impedance input can turn a driver on at power up and put a signal on the bus before the controller is ready. Tying both enable pins to fixed levels is legal only when the driver is meant to be permanently on, and a bus that takes turns needs at least one of them under control.

How SUPERB supports this line item

We supply the SN65LBC172ADWR for backplane and legacy board builds, with the row and the moisture level stated on the offer. Customers replacing an older quad driver can start from our pin to pin cross reference page, which lists the five families this part is pin compatible with and the enable polarity of each.

Where a board is being kept in production past the life of its original driver, the last time buy and LTB planning page describes how we size a final order against the remaining build plan.