TPS54341DPRR
Product Specifications
TPS54341DPRR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54341DPRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54341DPRR: 42 V, 3.5 A step-down regulator with power good and sequencing
TPS54341DPRR is a 3.5 A step-down regulator with an integrated 87 milliohm high side switch rated to 42 V in a WSON body of 10 pins. It is the sequencing member of the 42 V family: the soft start pin doubles as a tracking input, and an open drain power good asserts when the output is inside 93 to 106 per cent of nominal. The switching frequency is set by a resistor from 100 kHz to 2.5 MHz or taken from an external clock, and the device survives load dump pulses to 45 V under ISO 7637.
Order code and package
| TPS54341DPRR | Active, WSON-10 with thermal pad, 3000 pieces on a large reel, minus 40 to 85 degrees ambient |
| TPS54341DPRT | Active, the same body, 250 pieces on a small reel |
| TPS54340 | the 5 A member of the family in an eight pin HSOP |
| Body | ten pin WSON with the thermal pad, smaller than the HSOP alternative |
| Reference | 0.8 V, plus or minus 1 per cent |
Electrical parameters that decide the application
| Input voltage | 4.5 V to 42 V operating, load dump to 45 V |
| Continuous current | 3.5 A |
| High side switch | 87 milliohm |
| Switching frequency | 100 kHz to 2.5 MHz, resistor set or clock synchronised |
| Quiescent current | 152 microamp in pulse skip, 2 microamp in shutdown |
| Power good window | 93 to 106 per cent of nominal |
| Undervoltage lockout | 4.3 V internal, adjustable through the enable divider |
| Soft start | set by a capacitor on the SS pin, also usable as a tracking input |
Family variants and how they differ
| SS pin | a capacitor sets the ramp, and driving the pin from another rail makes the output track it |
| PWRGD | open drain, low when the output is out of regulation, in thermal shutdown or disabled |
| TPS54540 | 5 A, 92 milliohm, eight pin HSOP, no power good |
| TPS54340 | 3.5 A, 92 milliohm, eight pin HSOP, no power good |
| Thermal pad | on the underside, carries the ground return as well as the heat |
Points to check before this part goes on a BOM
The soft start pin is also a tracking input. A capacitor alone gives a ramp whose slope is set by the capacitor. Driving the pin from a divider off another rail makes this output follow that rail, which is how a 1.2 V core is kept below a 3.3 V input output rail at power up. That function is what separates this part from the plain members of the family.
The power good window is 93 to 106 per cent and it is not adjustable. A rail that sits at 92 per cent of nominal under load will report a fault even though the load is working. On a 3.3 V rail that is 3.07 V, which is inside the tolerance of many loads but outside the window of this pin. The window has to be checked against the load specification before power good is used as a enable for the next rail.
The addendum prints minus 40 to 85 degrees ambient. The device itself is specified to 150 degrees junction, and those two statements are consistent once the dissipation and the thermal resistance are accounted for. A customer who reads 85 degrees as the silicon limit will reject a part that is in fact usable at a much higher junction temperature.
87 milliohm at 3.5 A is 1.07 W during the on time. The WSON body passes that into the pad, and the pad is also the ground return. A pad with a few vias and a small copper area runs the junction well above the ambient, and the current rating alone does not tell anyone whether the board works. The thermal calculation is part of the electrical check, not an afterthought.
Synchronising to an external clock is useful on a multi rail board. Pulling the RT/CLK pin above the upper threshold turns it into a clock input, which lets several converters run at the same frequency and avoids the low frequency beat between them. The beat is what appears as a slow ripple envelope on a rail that feeds an ADC, and it is often blamed on the ADC rather than on the converters.
Current mode control needs a catch diode and a current sense element. The high side switch is integrated and the inductor current is sensed inside the part, so the external network is the inductor, the output capacitor, the catch diode and the compensation. The diode carries the full inductor current during the off time, so its forward drop is a direct efficiency loss at 3.5 A.
The 4.3 V lockout leaves little room on a 5 V rail. The converter will not start below 4.3 V, so a 5 V rail that sags during a load step has to stay above that. Raising the lockout with the enable divider protects against a slow brownout, and it also means the converter drops out earlier, which is the trade that divider makes.
Two amp of headroom over the load is the working rule. The 3.5 A rating is the switch current limit and the inductor peak sits above the DC output by half the ripple. At 3.5 A out with 30 per cent ripple the peak is 4.03 A, which is above the limit, so the usable continuous current is lower than the headline. The inductor value decides how much lower.
The ten pin body is often the reason for the part rather than the current. A 3.5 A converter in a small WSON frees board space that the eight pin HSOP equivalent would take, and the sequencing and power good pins come with it. On a dense board that combination is worth more than the extra ampere the 5 A member offers.
Tracking needs both rails measured with the same reference. When the soft start pin is driven from a divider off another rail, the divider tolerance becomes part of the tracking error. A 1 per cent pair keeps the two rails within a few tens of millivolt of their intended ratio, while 5 per cent parts can put the core rail above the input output rail at power up, which is what tracking exists to prevent.
Sequencing two rails from one input
The first rail is started with its own soft start capacitor. Its power good pin, pulled up to a logic rail, enables the second converter once the first is inside its window.
The second rail can then track the first through its soft start pin, which keeps the two outputs in a known order during both power up and a brownout recovery.
Where this order code fits
It supplies 3.5 A on 12 V and 24 V buses where the rail has to be sequenced and a power good output has to tell the next converter when to start. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does this part need an external diode? Yes. Only the high side switch is integrated, so a catch diode is required. It carries the inductor current in the off time and its forward drop is part of the loss at 3.5 A.
Can it be synchronised to another converter? Yes. Pulling the RT/CLK pin above its upper threshold turns the pin into a clock input. That removes the beat frequency between converters on the same board.
What does the power good output indicate? It is open drain and asserts low when the output is outside 93 to 106 per cent of nominal, in thermal shutdown, in dropout or disabled. It needs a pull up to the logic rail of the device that reads it.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.