TPS63031DSKR
Product Specifications
TPS63031DSKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS63031DSKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS63031DSKR single inductor buck boost at 800 mA
The TPS63031DSKR is the fixed 3.3 V member of the TPS6303x family, a four switch buck boost converter with 1 A switches that runs from 1.8 V to 5.5 V and holds a 3.3 V rail across the whole single cell discharge. It delivers 800 mA at 3.3 V in step down and 500 mA in boost, switches at a fixed frequency, and reaches 96 per cent efficiency. The body is the DSK WSON of ten pins, small enough to sit next to the load it feeds.
The quiescent current is 25 microamp typical and 35 microamp maximum, the shutdown current is 0.1 microamp typical and 0.9 microamp maximum, and the undervoltage lockout is 1.4 V to 1.6 V on a falling supply, which lets the part run from two alkaline cells as well as from a lithium cell. The average switch current limit is 900 mA minimum, 1000 mA typical and 1300 mA maximum, and that window is what sets the real output current in boost mode.
The adjustable member of the family, the TPS63030, uses a 500 mV feedback reference with a 495 mV to 505 mV window, and this fixed member ties the divider inside the package. A board that needs a level other than 3.3 V takes the adjustable part and a resistor pair, and a board that needs exactly 3.3 V takes this one and saves two components and a tolerance term.
Key parameters from the SLVS696D document
| Input range | 1.8 V to 5.5 V |
| Output | 3.3 V fixed on this member, adjustable on the TPS63030 |
| Output current | 800 mA at 3.3 V in step down, 500 mA in boost |
| Switching frequency | Fixed frequency PWM with synchronous rectification, power save mode at light load |
| Efficiency | Up to 96 per cent |
| Switch current limit | 900 mA minimum, 1000 mA typical and 1300 mA maximum average |
| Quiescent current | 25 microamp typical and 35 microamp maximum |
| Shutdown current | 0.1 microamp typical and 0.9 microamp maximum with the enable low |
| UVLO | 1.4 V to 1.6 V on a falling supply |
| Load disconnect | Load disconnected from the input during shutdown in the four switch topology |
| Soft start | Internal ramp with a short circuit protection that reduces the current limit |
| Package | DSK WSON of ten pins, operating range minus 40 to plus 85 degrees ambient |
Load disconnect is the feature that is easy to overlook
In a four switch topology the load is disconnected from the input when the converter is shut down, because two of the four switches are open. A two switch boost converter cannot do that: its inductor and its body diode form a path from the input to the output even when the part is disabled, and a product that is switched off still drains its battery through the load. On a single cell product with a long shelf life, that path is the difference between a year on the shelf and a month.
The current limit window is wide, 900 mA to 1300 mA, and that spread matters in boost mode. At 1.8 V input and 3.3 V output the input current is nearly twice the output current, so the 500 mA output rating is a switch limit statement rather than a thermal one. A product that draws 500 mA at 3.3 V from a nearly empty cell is drawing about 1 A at the input, which is at the top of the switch window rather than comfortably inside it.
Soft start and short circuit protection are linked in this family. The part ramps the output with a controlled current, and if the output does not reach regulation within the start up window it enters a protection mode where the current limit is reduced to less than half of the nominal value. That behaviour protects the battery and the inductor, and it also means that a board with a large output capacitance and a heavy load can fail to start rather than start slowly.
Where this part fits
Single cell and two cell battery products with a 3.3 V rail, handheld meters, portable audio, wireless sensors and any board that has to run down to 1.8 V without a second converter. Our cross reference notes are at power management cross reference and the pin to pin notes are at pin to pin cross reference.
What to check before a purchase order
Check the fixed voltage versus the adjustable part. The 63030 and the 63031 share a document and a pinout, and the difference is whether the divider is internal. A board that was routed for the adjustable part and populated with the fixed one will have a divider driving a pin that is already tied internally, and the output will not be what either part was set for.
Check the output current at the bottom of the input range. The 500 mA boost rating and the 900 mA minimum switch limit leave less margin than the headline suggests, and a load that draws its peak at low battery will find the limit before the thermal limit. The receipt check we run on these reels is at incoming inspection plan.
Questions that come up on this part
Can the part start into a 100 microfarad output capacitor, is a common question. It can, provided the load is light at start up and the input can supply the inrush, because the soft start limits the current and the protection mode reduces the limit further if the output fails to rise. A board with a large capacitor and a heavy load at start up needs a load switch or a sequenced enable rather than a larger converter.
The second question is whether the 3.3 V level holds below 3 V input. It does, because the part is in boost mode there, and the output stays at 3.3 V while the input falls to below 2 V. What falls is the available current, since the switch limit caps the input current and the input current rises as the input voltage falls.