Contact Us

TPS62993QRYTRQ1

Brand: Texas Instruments
Texas Instruments TPS62993QRYTRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62993QRYTRQ1 — Power Management & Signal Chain | Superb Automation

TPS62993QRYTRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62993QRYTRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62993QRYTRQ1 3 A automotive buck rated to 165 degrees junction

The TPS62993QRYTRQ1 is an automotive step down converter that takes 3 V to 10 V in and delivers 3 A, in a body and a qualification that let it run with a junction temperature up to 165 degrees. The switch resistances are 62 milliohm on the high side and 22 milliohm on the low side, the quiescent current is 4 microamp typical, and the switching frequency is selectable at 1 MHz or 2.5 MHz. Output accuracy is 1.5 per cent across the full operating temperature range rather than at 25 degrees only.

The 10 V input rating is a deliberate limit and it is the first thing to check. This part is for rails that sit behind a protected supply: a 5 V or 9 V intermediate rail, a pre regulated automotive node, a sensor supply. The 18 V members of the same document cover the rails that see the battery directly, and the two families share a package and a control scheme but not a voltage rating.

Automotive qualification is AEC-Q100, and the temperature story is the reason for the part. A converter in a dashboard or near an engine bay sees an ambient that a consumer part cannot survive, and the 165 degree junction rating is what allows a 3 A rail to be placed there without a derating argument. The thermal shutdown window is 168 to 185 degrees with 12.5 degrees of hysteresis, so a part that reaches the limit folds back and recovers rather than latching.

Key parameters from the SLVSGV5A document

Input range3 V to 10 V on this member, 3 V to 18 V on the other members of the document
Output current3 A rated
Output voltage0.6 V to 5.5 V with an external divider, sixteen preset values through the internal divider
Switching frequency1 MHz or 2.5 MHz selectable, with auto PFM and forced PWM modes
High side resistance62 milliohm
Low side resistance22 milliohm
Quiescent current4 microamp typical in power save mode with no load
Shutdown current0.27 microamp typical and 3.5 microamp maximum
Output accuracy1.5 per cent across the full operating temperature range
Power goodThreshold at 93 per cent falling and 99 per cent rising, with 1.5 per cent of hysteresis
Thermal shutdown168 to 185 degrees, 12.5 degrees of hysteresis, junction rated to 165 degrees
QualificationAEC-Q100 with 2 kV human body model ESD on all pins

What a 165 degree junction rating changes

Most converters are rated to 125 or 150 degrees junction, and the difference is not academic. A part near a heat source in a sealed automotive module can run at an ambient of 105 degrees, and with a thermal resistance that puts the junction 40 degrees above ambient, a 150 degree part is at its limit while a 165 degree part has margin. That margin is what allows a 3 A rail to be placed in a location where the alternative is a longer, noisier cable.

The 1.5 per cent accuracy over temperature is the second consequence. A current mode converter with an internal reference drifts with temperature, and the drift is usually quoted at 25 degrees and described as typical. On a rail that feeds an ADC reference or a sensor bridge, the drift over minus 40 to plus 165 degrees is the error that shows up in a calibration that was done at room temperature.

The 10 V input limit is the constraint to plan around. On a 5 V rail the part has 2 V of headroom at the worst case, which is enough for a 2.5 MHz conversion at 3 A. On a 9 V rail the duty cycle is short and the high side conduction is brief, so the loss moves into the low side and the inductor. On a 12 V rail the part must not be used, even though a 12 V nominal supply looks close, because the transient headroom is not there.

Where this part fits

Automotive sensor and camera supplies, ADAS module rails behind a protected node, body control modules and any automotive board where a 3 A rail has to run hot and stay accurate. Our cross reference notes are at power management cross reference and the drop in check is at how to verify a drop in replacement.

What to check before a purchase order

Check the input rating against the node, not against the module. The 993 is the 10 V member, the 992 and the 903 cover 18 V, and the parts share a document and a family name that does not encode the voltage. A module that was validated at 9 V and then moved to a battery connected node needs a different member, and the difference is one digit.

Check the output configuration: external divider or one of the sixteen preset levels. A board populated for a preset level and fitted with the divider version will regulate at the reference instead of at the rail, which reads as a converter fault during first article inspection. The receipt check we run is at incoming inspection plan.

Questions that come up on this part

Can the part run at 165 degrees junction continuously, is the first question. It can run there within the electrical limits, but the thermal path has to deliver the heat out of the package at that temperature, and the efficiency falls as the junction rises because the switch resistance rises with it. A 3 A rail at 165 degrees is a different thermal problem from the same rail at 85 degrees, and the copper area has to be sized for the former.

The second question is whether the part survives a reverse battery connection. It does not have reverse polarity protection on the input, so the module needs a blocking element upstream. That is true of most converters in this class, and the assumption that a converter is protected because it is automotive qualified is one of the more expensive assumptions in a vehicle electrical architecture.