Contact Us

TPS6286A06VBMR

Brand: Texas Instruments
Texas Instruments TPS6286A06VBMR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS6286A06VBMR — Power Management & Signal Chain | Superb Automation

TPS6286A06VBMR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS6286A06VBMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS6286A06VBMR 6 A buck in a 2 mm by 3 mm QFN

The TPS6286A06VBMR is the 6 A member of the TPS6286Axx and TPS6286Bxx families, a synchronous step down converter that runs from 2.4 V to 5.5 V and switches at 1.2 MHz. It delivers 6 A from a QFN body of 2 mm by 3 mm with an exposed pad, and the family adds 8 A and 10 A members in the same body, so a board that was signed off at 6 A can be reworked upward without a change to the copper as long as the inductor and the input capacitors are rechecked.

The A version has an external feedback divider and an adjustable soft start capacitor on the SS pin. The B version replaces the divider with an I2C interface and adds a power good output, which is the choice when the rail voltage has to change at run time. Both share the power stage, the 1.2 MHz oscillator, the quiescent current of 5.1 microamp typical and 9 microamp maximum, and the undervoltage lockout window of 2.2 V to 2.4 V.

The current class is what a modern processor needs. A 6 A rail at 0.9 V is a core supply for a small application processor or an FPGA, and at 1.2 MHz the inductor is in the 470 nanohenry class with a saturation current above the current limit. Thermal shutdown sits at 150 degrees junction, the output discharge path is internal, and the soft start ramp on the 8 A member is quoted at 0.4 to 0.72 milliseconds, which is the figure to size the power up sequence around.

Key parameters from the SLUSFG2C document

Input range2.4 V to 5.5 V, UVLO between 2.2 V and 2.4 V
Output current6 A on this member, 8 A and 10 A on the other two
Output voltageSet by an external divider on the A version, by I2C on the B version
Switching frequency1.2 MHz nominal
Quiescent current5.1 microamp typical and 9 microamp maximum, device not switching
Soft startAdjustable with a capacitor on the SS pin, 0.4 to 0.72 milliseconds on the 8 A member
Power goodOpen drain on the B version, with a window around the nominal output
Output dischargeInternal, active when the converter is disabled
Thermal shutdown150 degrees junction
Inductor470 nanohenry in the application circuit of the document
PackageQFN of 2 mm by 3 mm with an exposed pad, VBM body
AccuracyFixed voltage operation quoted in the 0.7 per cent class in FPWM with no load

What 6 A in a 2 mm by 3 mm body asks of the board

The package is small for the current, so the exposed pad is the whole thermal path. At 6 A and 5 V to 1 V the conduction loss in the converter is a large part of a watt, and that heat leaves through the pad and the vias under it rather than through the plastic. A board with eight thermal vias and two square centimetres of copper on the underside will hold the rating; a board with four vias and a thin pour will not, and the converter will reach thermal shutdown before it reaches the current limit.

The 1.2 MHz carrier is a compromise. A higher frequency would shrink the inductor further and a lower one would raise efficiency, and 1.2 MHz sits where a 470 nanohenry part is available in a small case with a saturation current above the 6 A rating. The input capacitor carries the full pulsed current, so a 22 microfarad ceramic close to the drain of the high side switch is not optional, and a second one on the other side of the body is cheap insurance.

The difference between the A and the B version is more than the interface. The B version brings a power good signal and a register set that can change the output voltage, and it removes the divider that would otherwise add a tolerance term and a noise pickup node. On a board that ships in several variants with different core voltages, the B version lets one bill of materials serve all of them, which is usually worth more than the cost difference.

Where this part fits

Processor and FPGA core rails, DDR memory supplies, ASIC rails in a network appliance and any board that needs 6 A from a 3.3 V or 5 V bus in a small area. Our cross reference notes for the family are at power management cross reference and the drop in check is at how to verify a drop in replacement.

What to check before a purchase order

Check the interface letter and the current digits together. TPS6286A06 is 6 A with an external divider, TPS6286A08 and TPS6286A10 are 8 A and 10 A with the same divider, and the B members carry the I2C interface instead. The bodies are the same size, so a reel with the wrong letter will fit the board and behave differently at power up.

Check the inductor saturation current against the current limit, not against the 6 A rating. A part that trips into hiccup at full load is usually a part whose inductor saturated, and the symptom looks like a converter fault. The receipt and marking check we run is at incoming inspection plan.

Questions that come up on this part

Is 6 A available at 2.5 V input, is a common question. The current limit is above the rating, but at 2.5 V input with a 1 V output the duty cycle is 40 per cent, the high side conducts for less than half the period, and the resistive loss in the switches and the inductor decides the usable current. A rail that must hold 6 A at the bottom of the input range needs the thermal check at the enclosure temperature.

The second question is whether the A and B versions can be mixed on one board. Electrically the pins match except that the feedback divider becomes the bus connection on the B version, so a board that carries both has to be able to isolate the divider. Mixing them without that change leaves a divider fighting a register, and the output settles at a level that belongs to neither.