Contact Us

TPS62625YFFR

Brand: Texas Instruments
Texas Instruments TPS62625YFFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62625YFFR — Power Management & Signal Chain | Superb Automation

TPS62625YFFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62625YFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62625YFFR 600 mA at 6 MHz in a chip scale package

The TPS62625YFFR is the 600 mA member of the TPS6262x family, a synchronous step down converter that runs at a 6 MHz regulated frequency and takes 2.3 V to 5.5 V in. It is built for a chip scale package and for a 1 microhenry or smaller inductor, which is what a 6 MHz carrier allows: at that rate the ripple current for a 600 mA rail stays inside a chip inductor the size of a grain of rice. Quiescent current is 31 microamp, efficiency is quoted at 90 per cent at 6 MHz, and total DC accuracy is 2 per cent.

The loop is not a conventional fixed frequency PWM. It uses a frequency locked ring oscillator modulator, which behaves like a hysteretic comparator with an internal frequency lock loop holding the switching rate near 6 MHz as the input and the load move. That gives the fast transient response of a hysteretic loop with a switching spectrum that is stable enough to filter. The oscillator is specified from 5.4 MHz to 6.6 MHz, and the current limit on the P-channel switch is 975 mA minimum, 1100 mA typical and 1200 mA maximum.

Line regulation is 0.13 %/V and load regulation is quoted as 0.0003 %/mA, both of which are numbers that only a fast loop can produce. Thermal shutdown is at 140 degrees junction with 10 degrees of hysteresis, which is lower than the 150 to 170 degrees of the larger families and reflects the small package and the limited thermal path. The P-channel on resistance is 350 milliohm at 2.5 V in PWM mode.

Key parameters from the TPS6262x document

Input range2.3 V to 5.5 V, single cell lithium with an extended range
Output600 mA rated, with 2 per cent total DC accuracy
Switching frequency6 MHz regulated, specified from 5.4 MHz to 6.6 MHz
ControlFrequency locked ring oscillator modulator with automatic PFM and PWM switching
Quiescent current31 microamp typical and 55 microamp maximum in PWM mode with no load
Shutdown current7.6 microamp quoted for the shutdown condition in the electrical table
Current limitP-channel limit 975 mA minimum, 1100 mA typical and 1200 mA maximum
On resistance350 milliohm P-channel at 2.5 V input in PWM mode
RegulationLine 0.13 %/V, load 0.0003 %/mA, both measured in PWM mode
Efficiency90 per cent at 6 MHz operation at the quoted point
Thermal shutdown140 degrees junction with 10 degrees of hysteresis
PackageChip scale ball grid array, YFF body, with the inductor the largest component on the rail

What 6 MHz does to a 600 mA rail

At 6 MHz the inductor for a 600 mA rail can be 0.47 microhenry to 1 microhenry and still keep the ripple under 200 mA peak to peak, which means the whole converter including the inductor fits in a few square millimetres. The output capacitor can be a single 4.7 microfarad ceramic. That density is the reason the part exists: it is not the most efficient converter in the catalogue, it is the one that fits behind a display or inside a module where nothing else will.

The switching loss at 6 MHz is significant, and the 90 per cent efficiency figure reflects it. At 3.6 V in and 1.8 V out the part is turning the FETs six million times a second, and the gate charge and drain capacitance are paid at that rate regardless of load. Below a few milliamps the loop drops into PFM and the rate falls, which is what keeps the light load efficiency respectable and the quiescent current at 31 microamp.

The frequency lock loop is what makes the spectrum usable. A plain hysteretic converter varies its rate with input and load, which spreads the emissions over a band and makes a filter hard to specify. Holding the rate near 6 MHz puts the fundamental and its harmonics in known places, so a small input filter and a careful ground can meet an emissions limit without a shielded inductor.

Where this part fits

Wearables, hearables, camera modules, display bias rails and any product where a 600 mA rail has to fit in a space smaller than the connector next to it. Our desk keeps the cross reference for the chip scale class and the substitution notes, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

Check the marking and the voltage option. Six parts share this document and this package, from 1.2 V to 1.8 V and beyond, and a substitution changes the rail without changing the footprint. On a chip scale package the marking is a few characters, so the receipt check has to be done against the reel label and a sample, not by eye on the board.

Check the thermal path. A 140 degree thermal shutdown in a package this small is reached quickly at 600 mA in a sealed enclosure, and the copper under the balls is the only heat spreader. A board that puts the part in a corner with no plane will shut down at a load the datasheet says it can carry. See incoming inspection plan for the goods inwards check on this body.

Questions that come up on this part

Can a 6 MHz converter be used next to a radio, is the obvious question. It can, if the fundamental and its harmonics are kept out of the receive band and the switch node is short. A 6 MHz carrier has harmonics at 12, 18 and 24 MHz, which sit inside the short wave band but below most of the bands a handset uses, so the interference risk is more about the loop's own variation than about the carrier.

The second question is whether the 600 mA rating is available at 2.3 V input. It is, but the P-channel resistance of 350 milliohm at 2.5 V sets the drop, and in dropout the output follows the input. A rail that has to hold its voltage at the end of a cell discharge needs a bigger inductor and a lower resistance part, not a higher current rating.