Contact Us

TPS62240DRVR

Brand: Texas Instruments
Texas Instruments TPS62240DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62240DRVR — Power Management & Signal Chain | Superb Automation

TPS62240DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62240DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62240DRVR adjustable 300 mA at 2.25 MHz in a 2 mm by 2 mm WSON

The TPS62240DRVR is the adjustable member of the TPS6224x family, a synchronous step down converter that takes 2 V to 6 V in and delivers up to 300 mA at a fixed 2.25 MHz, in a 6 pin WSON body of 2 mm by 2 mm or the 5 pin SOT alternative. The output is set by two resistors from a 600 mV class reference, the family quotes better than 94 per cent efficiency, and the converter enters power save mode at light load with a quiescent current of 15 microamp. Two fixed voltage siblings, the TPS62242 and TPS62243, share the document.

The input range is the interesting part for battery work: 2 V minimum is below the end of discharge of a single lithium cell and inside the range of two alkaline cells, and the 6 V ceiling covers a 5 V rail with margin. The converter holds 100 per cent duty cycle, so when the cell voltage falls close to the output the part passes the input through with only the resistive drop, which is what keeps a 1.8 V rail alive on a nearly flat cell. The MODE pin selects between power save and forced PWM, and shutdown current is under 1 microamp.

The 2.25 MHz rate allows a 2.2 microhenry inductor and a 10 microfarad ceramic output capacitor, both of which fit in a 2 mm wide strip next to the package. Output accuracy in PWM is quoted at 1.5 per cent, the operating ambient range is minus 40 to 85 degrees, and the body is small enough that the thermal path runs through the pins and the exposed pad into the copper rather than through the package. At 300 mA the dissipation is modest, but at 5 V in and 1.2 V out the low side carries most of the period.

Key parameters from the SLVS762C document

Input range2 V to 6 V, covering a single lithium cell, two alkaline cells and a 5 V rail
OutputAdjustable on this member, up to 300 mA, fixed 1.8 V and other options on the siblings
Switching frequency2.25 MHz fixed, with power save operation at light load
Accuracy1.5 per cent in PWM mode, set by the external divider on this member
EfficiencyBetter than 94 per cent at the quoted operating point
Quiescent current15 microamp with the mode pin low and the device not switching
Shutdown currentUnder 1 microamp with the enable pin low
Duty cycle100 per cent for the lowest dropout, which passes the input through at the resistive drop
Typical components2.2 microhenry inductor, 4.7 microfarad input and 10 microfarad output ceramic
Ambient rangeMinus 40 to 85 degrees
Package6 pin WSON, 2 mm by 2 mm, DRV body, or the 5 pin SOT alternative

Running a 1.8 V rail down to a flat cell

The useful window for a 1.8 V output from a single cell is narrow. A lithium cell delivers 4.2 V fresh and about 3.0 V at the end of discharge, so the converter runs in buck mode for most of the cycle and only approaches dropout at the very end. The 100 per cent duty cycle mode is what covers that last part: below about 2.1 V of input the part stops switching and the output follows the input less the drop across the high side FET and the inductor.

In dropout the output is no longer regulated, and the load sees whatever the cell can deliver. That is acceptable for a device that shuts down at 2.4 V, and it is not acceptable for one that expects 1.8 V until the last moment. The board level decision is where the low battery threshold sits relative to the dropout point, and the converter data cannot make that decision.

The 2.25 MHz rate helps in the same direction, because the ripple current is small enough that a 2.2 microhenry inductor can be used, and a small inductor has a low DC resistance, which is what determines the dropout voltage in the pass through mode. A physically larger inductor would have lower resistance still and a lower dropout, at the cost of board area.

Where this part fits

Single cell handhelds, Bluetooth headsets, portable instruments, WLAN modules and any board that needs 300 mA at 1.8 V or 1.2 V from a battery in a 2 mm by 2 mm body. Our desk keeps the cross reference and the substitution notes for this family, see power management cross reference and how to verify a drop in replacement.

What to check before a purchase order

Check which member the board needs. This is the adjustable one, so the output voltage lives in two resistors on the board rather than in the order code, and a substituted fixed member will ignore the divider and regulate to its own voltage. The DRV body is the 6 pin WSON and the SOT is a 5 pin body with a different pin count, so the two are not interchangeable on an existing board.

Check the inductor against the switch current limit rather than the 300 mA rating, and check the divider against the reference tolerance. The divider current also adds to the light load current, so a low value pair that improves noise immunity will cost part of the 15 microamp standby figure. See incoming inspection plan for the goods inwards check on this body.

Questions that come up on this part

Is 2 V input really usable, is a question that comes up on every two cell product. It is, with the part in dropout and the output following the input, so a 1.8 V rail is only held while the cells are above about 2.1 V under load. A pair of alkaline cells at end of life will sit below that under a 300 mA draw, and the rail will sag with them.

The second question is about the difference between the fixed members and this one. The fixed parts remove the divider and its leakage, and they hold their accuracy through an internal trim; the adjustable part gives a rail that can be set to any value in the range, at the cost of two resistors, a leakage term and a tolerance term. For a volume product with one rail the fixed part is the better choice, and for a development board the adjustable one is.