Contact Us

TPS54116QRTWTQ1

Brand: Texas Instruments
Texas Instruments TPS54116QRTWTQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS54116QRTWTQ1 — Power Management & Signal Chain | Superb Automation

TPS54116QRTWTQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS54116QRTWTQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS54116QRTWTQ1: the DDR power stage that pairs a 4 A buck with a 1 A termination regulator

TPS54116QRTWTQ1 is a single chip DDR memory supply. One half is a 4 A synchronous buck that produces the main memory rail, the other half is a 1 A source and sink linear regulator that produces the termination rail at half the main rail, and a buffered reference output tracks the same half voltage for the address and command lines. The whole thing sits in a 24-pin WQFN measuring 4 mm by 4 mm.

The reason this belongs in one package rather than three is the tracking requirement. The termination rail has to sit at half of VDDQ and it has to follow VDDQ while VDDQ is ramping, because a memory bus that sees the termination rail arrive late or at the wrong level will drive current through the termination resistors during the ramp. The reference output and the termination regulator are both derived from the same internal divider, so the three rails move together by construction rather than by a supervisor sequencing them.

The numbers below come from SLVSCO3B, revised October 2016, and from the orderable addendum in the same document.

What the order code sits on

Functionstep-down converter plus DDR termination regulator in one body
Input range2.95 V to 6 V
Buck output4 A continuous, integrated FETs
High-side FET33 milliohm
Low-side FET25 milliohm
Controlfixed frequency current mode
Switching frequency100 kHz to 2.5 MHz, resistor set, synchronizable to an external clock
Voltage reference0.6 V with 1 percent accuracy over temperature
Current limitcycle by cycle peak, adjustable with a resistor at ILIM
Termination regulator1 A source and sink, DC accuracy plus or minus 20 mV
Termination capacitorstable with two 10 microfarad ceramic parts
Reference output10 mA buffered, 49 to 51 percent of VDDQ
Shutdown current1 microamp with both enables low
PackageWQFN RTW, 24 pins, 4.00 mm by 4.00 mm
Junction rangeminus 40 to plus 150 degrees
Reel in this page250 pieces on a small reel, moisture level 2

Why 2.5 MHz is offered in a memory supply

The switching frequency range runs from 100 kHz to 2.5 MHz and the top of that range is there for a specific problem: the medium wave radio band sits just above 500 kHz, and a converter running near it radiates into an AM receiver that shares the enclosure. Setting the frequency above the band, or synchronizing the converter to a clock that is outside it, moves the switching energy away from the receiver without shielding. The same argument applies to any product that has a radio and a memory rail in the same box.

Running at 2.5 MHz also shrinks the inductor and the output capacitors, which is what allows a 4 A rail in a 4 mm by 4 mm footprint to fit under a memory socket. The cost is switching loss: the 33 milliohm high-side FET is on for a smaller fraction of the period at a higher frequency, but every transition costs energy, and the efficiency at 2.5 MHz is lower than at 500 kHz for the same load. A product that does not have an AM radio constraint usually runs this part between 500 kHz and 1 MHz.

External synchronization is the third option. The converter follows a clock that the system already has, which puts every switching edge in the box on a known phase and keeps the beat products out of a receiver's passband. A rail that is synchronized also starts and stops with the clock, so the sequencing of several rails can be arranged by the clock rather than by the enable pins.

The termination half and its two capacitor requirement

The termination regulator sources and sinks 1 A and holds the rail within 20 mV of the target, which is what a DDR bus needs when the data lines switch in both directions. A regulator that can only source would let the rail rise when the bus discharges into it, and one that can only sink would collapse when the bus pulls current. The sink capability is also what discharges the rail when VDDQ is removed, together with the discharge that the enable pin performs on shutdown.

The output capacitor requirement is stated as two 10 microfarad ceramic parts, and it is a stability requirement rather than a recommendation. Ceramic capacitors lose capacitance under DC bias, so a pair of 10 microfarad parts at 1.2 V may measure well below their nominal value, and a build that substitutes a single 22 microfarad part of a different dielectric can end up outside the stable region. The same warning applies to the small case sizes, where the bias derating is largest.

The buffered reference output is a separate 10 mA source that tracks VDDQ at half. It drives the termination resistors on the address and command lines, which are a DC load and do not need the source and sink capability of the termination regulator. Keeping the two separate is what stops the switching noise on the data lines from appearing on the reference that the address lines use.

Enables, UVLO and start-up order

Both halves have independent enable pins, and both have adjustable undervoltage lockout with hysteresis set by a resistor divider. That arrangement lets a board hold the memory rail off until the input supply is above a chosen level, and hold the termination rail off until the main rail is up, without an external sequencer. The order matters: if the termination rail comes up first, the address lines are pulled to a voltage that has no reference, and some memory devices draw current through their input protection until VDDQ arrives.

Start-up into a pre-biased output is supported, which happens when the memory rail is held up by another path while the converter is still disabled. The converter does not discharge the output before it starts; it begins switching and ramps from the level it finds. A product that has a backup battery on the memory rail depends on this behaviour.

Thermal limits in a 4 mm body

The junction range goes to 150 degrees, which is wider than the ambient range of most boards, and that is deliberate: the part is expected to run hot inside a small enclosure and the limit is a junction figure. At 4 A into 1.2 V from a 5 V input the buck dissipates a few tenths of a watt in the FETs plus the switching loss, and the 24-pin body with its thermal pad passes that into the board copper.

The termination regulator dissipates according to the differential across it. At 1.2 V VDDQ and 0.6 V termination the differential is small, but the current is 1 A, so the part still drops 0.6 W when it is sourcing at full load. That loss sits in the same package as the buck, and a board that loads the termination rail heavily while the buck runs at full current has both losses in one thermal pad. The copper under the pad is the only path out, which is why the vendor's land pattern is not optional.

Carriers and what the addendum prints

TPS54116QRTWTQ1WQFN RTW, 24 pins, 250 pieces on a small reel, active
TPS54116QRTWRQ1same body, 3000 pieces on a large reel
Lead finishNIPDAU
Moisture levelLevel-2-260C-1 YEAR
Operating temperatureminus 40 to plus 125 degrees ambient on the addendum row
QualificationAEC-Q100 grade 1, HBM level 2, CDM level C6
Body size4.00 mm by 4.00 mm including the thermal pad
Reel choicethe T suffix is the small reel, the R suffix the large one

The T suffix on this string is the reason it appears in prototype kits. A 250 piece reel is enough for a pilot build and for the samples a customer wants before a production release, while the production order moves to the R suffix and the 3000 piece reel. Both rows are active, so the choice is about quantity rather than availability.

AEC-Q100 grade 1 with HBM level 2 and CDM level C6 is worth quoting to an automotive customer early, because the ESD classification is often the first question in a supplier review. The part is a memory supply rather than a safety element, so the functional safety documentation question does not usually arise.

Where this part fits and where it does not

The obvious socket is an embedded computing board with DDR3 or DDR3L memory and a 5 V input, where the memory rail and its termination would otherwise need three devices and a sequencing scheme. The part is also used in set-top boxes, industrial single board computers and any product where the memory is soldered down and the rail is generated on board.

It is the wrong part when the memory rail needs more than 4 A, when the input is above 6 V and has to come down in one stage, or when the memory is DDR4 at a voltage where the termination scheme differs. In those cases the buck and the termination regulator are separate devices, and the tracking between them becomes a system problem.

When a customer is looking for a substitute for an older DDR supply, the comparison is about the termination accuracy, the reference divider ratio and the enable logic, not only the current rating. Our power management cross reference page lists the rows we check first, and the pin to pin cross reference page covers the case where the package has to match an existing land pattern.

Questions buyers ask before a first order

Does it need an external VTT reference divider? No. The reference is internal and the buffered output tracks VDDQ at half, so the divider that older schemes needed is not part of this circuit.

Can the two halves be enabled separately? Yes, and the enable pins have their own adjustable UVLO thresholds. A board that ties them together loses the ability to sequence the termination rail after the main rail.

What sets the current limit? A resistor at the ILIM pin, which sets the peak current at which the converter stops switching cycle by cycle. The value is chosen for the inductor saturation current rather than for the load, so a smaller inductor needs a lower limit.

Is the part available on a small reel for a pilot build? Yes, this string is the 250 piece small reel. The production quantity moves to the R suffix.