Contact Us

ADF4159CCPZ-RL7

Brand: Analog Devices
Analog Devices ADF4159CCPZ-RL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADF4159CCPZ-RL7 — Analog & Mixed-Signal ICs | Superb Automation

ADF4159CCPZ-RL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADF4159CCPZ-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADF4159CCPZ-RL7: a 13 GHz synthesizer that also generates the sweep

The ADF4159CCPZ-RL7 is a fractional N frequency synthesizer from Analog Devices with a feature set aimed at radar rather than at a plain local oscillator: it generates sawtooth, triangular and parabolic frequency ramps in the part, superimposes FSK or PSK on a ramp, and reports the instantaneous frequency back to the host. It reaches 13 GHz at the RF pins, runs a phase frequency detector at up to 110 MHz, and quotes a normalised phase noise floor of minus 224 dBc per hertz.

What the vendor publishes

ParameterValue
RF bandwidthto 13 GHz
Modulus25 bit fixed
Phase frequency detectorup to 110 MHz
Phase noise floorminus 224 dBc per hertz, normalised
Modulationsawtooth, triangular and parabolic ramps, two sweep rates, ramp delay
SuperimposedFSK and PSK, ramp with two different sweep rates
Readbackfrequency readback and interrupt
Phaseprogrammable phase control
Supply2.7 V to 3.45 V analog, 1.8 V digital
Interface3 wire serial, digital lock detect
ESD3000 V human body model, 1000 V charged device model

Step size is a division, not a number on the front page

A fixed 25 bit modulus is 33,554,432. With a 110 MHz phase frequency detector the step is 3.278 Hz, at 100 MHz it is 2.98 Hz, at 10 MHz it is 0.298 Hz and at 1 MHz it is 0.030 Hz. The claim of sub hertz resolution therefore depends on the reference the system chooses: it holds below a 33.5 MHz detector frequency and stops holding above it. For an FMCW radar the number that matters is not the step but the step multiplied by the number of steps in a sweep, because that product is the sweep linearity the part has to hold.

Where the in band noise floor lands

The normalised floor of minus 224 dBc per hertz is referred to a 1 Hz comparison, and translating it to the output takes the division ratio and the detector frequency. At 10 GHz out of a 100 MHz detector the ratio is 100, which adds 40 dB, and the detector term adds 80 dB, so the in band floor is about minus 104 dBc per hertz. At 13 GHz out of the same detector the ratio is 130 and the floor is minus 101.7 dBc per hertz. Two conclusions follow: the same chip gives 2.3 dB worse phase noise at the top of its range, and a lower detector frequency trades step size against noise.

The ramp features that decide the radio

Sawtooth, triangular and parabolic ramps in the synthesizer remove the need for a digital to analog converter driving the tuning input, which is where most of the linearity error in a low cost radar front end comes from. Two sweep rates on one ramp, with a programmable delay between them, is what a chirp sequence with a settling gap needs. Frequency readback and an interrupt mean the host can timestamp the sweep without a dedicated timer, and the FSK and PSK functions let a communication waveform share the same loop.

Two questions buyers ask

13 GHz at the pins or a multiplier after a lower band part? A multiplier adds conversion loss, an amplifier and a filter, and it multiplies the phase noise by the multiplication ratio. A single chip that reaches 13 GHz avoids all three, which is why the part exists at the top of the fractional N range.

Does a plain local oscillator build need the ramp features? No, and a plain fractional N part is cheaper for a fixed frequency. The ramp features are worth paying for exactly when the product has to sweep, which is the radar and the test instrument case.

SUPERB quotes the ADF4159CCPZ-RL7 against this row and confirms the package and reel before shipment. Synthesizer and RF alternatives are compared under RF component sourcing, delivery on a build waiting for parts is covered by component lead time solutions, and the category index is analog and mixed signal ICs.

Request Quote — In Stock, 100% New & Original, Full Warranty