Contact Us

TPS51362RVER

Brand: Texas Instruments
Texas Instruments TPS51362RVER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS51362RVER — Power Management & Signal Chain | Superb Automation

TPS51362RVER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS51362RVER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS51362RVER: 22 V Input, 10 A Converter With the FETs Inside and 100 uA Standby

TPS51362RVER is a synchronous step-down converter with both FETs integrated in a 28-pin QFN body of 28 pins. It takes 3 V to 22 V at the input, holds 0.6 V to 2 V at 10 A, switches at a fixed 800 kHz, and drops its own bias current from 560 uA to 100 uA when the LP# pin is pulled low.

Order code and package

Ordering stringTPS51362RVER, QFN-28 (RVE), 3.5 mm by 4.5 mm by 1.0 mm, 0.4 mm pitch
Input3 V to 22 V at VIN, 4.6 V to 5.5 V at the V5 bias pin
Output0.6 V to 2 V adjustable through REFIN and REFIN2
Current10 A with the high-side and low-side FETs inside the package
Switching frequency800 kHz fixed, no resistor to set it, one frequency for the whole family
Output capacitorsD-CAP2 loop, works with POSCAP, SP-CAP or all ceramic
Temperature-10 C to +85 C ambient, the cold end is the constraint

Electrical parameters that decide the application

Bias current100 uA in ULQ mode with LP# low, 560 uA normal, 1 uA shutdown
Reference2 V at VREF, plus or minus 1 percent from 0 uA to 300 uA of load
Minimum off time320 ns, 25.6 percent of the 1.25 us period at 800 kHz
V5 undervoltage lockout4.3 V minimum, 4.4 V typical, 4.6 V maximum on the wake threshold
Thermal resistance40.2 C/W junction to ambient, 22.8 C/W junction to case top, 1.6 C/W bottom
Soft start10 uA into the SLEW capacitor, so the ramp time is set by capacitance
Current limittwo levels selected at the TRIP pin, low-side sensing, temperature compensated
Statuspower good output, output discharge, OVP at 120 percent typical

Points to check before this part goes on a BOM

The standby number is the feature: 100 uA in ULQ mode against 560 uA in normal operation is 460 uA saved, which is 876 mAh a year at the low figure and 4.9 Ah at the high one. On a 5000 mAh battery the difference between the two states is 17.5 percent of the pack over a year of shelf time, so LP# has to be driven by the system and not tied low by mistake.

The specified ambient range starts at -10 C, not -40 C. A product sold into an industrial cold start, a freezer or a winter vehicle cabin is outside the part at the bottom of the table, and the certification of the assembly follows the datasheet, not the marketing temperature line.

320 ns of minimum off time is 25.6 percent of the 1.25 us period, so the maximum duty is 74.4 percent. A 2 V output from a 3 V input needs 66.7 percent and fits, while the same 2 V output from a 2.5 V input needs 80 percent and does not: the converter falls out of regulation rather than tripping a protection, which shows up as a rail that sags instead of a fault flag.

Ten amps at 1.05 V is 10.5 W, and at 90 percent the loss is 1.17 W inside the 28-pin body. At 40.2 C/W that is a 47 C rise, so an 85 C ambient puts the junction at 132 C with no margin for the inductor loss that also lands on the same copper. The 1.6 C/W junction to case bottom figure is the path that saves it, which means the exposed pad and its vias are the thermal path and not an afterthought.

The 2 V reference is plus or minus 1 percent, which is 20 mV, and a 1.05 V output takes half of it through the REFIN divider, so 10 mV or 0.95 percent arrives from the reference alone before the two resistors contribute. A 1 percent resistor pair doubles that, and the total is the number that belongs on a rail accuracy line rather than the reference figure.

Current limit is sensed across the low-side FET and the feature list says it is temperature compensated, which is the right question to ask because an uncompensated RDS(on) sensor moves by tens of percent over the junction range. The TRIP pin offers two levels, so the same part serves a 6 A rail and a 10 A rail without a different order code.

The soft start ramp is a current into an external capacitor, 10 uA into the SLEW pin, so the time follows capacitance directly: 12.5 nF gives 1 ms to 0.8 V and 125 nF gives 10 ms. The same pin sets the integrator time constant, so a slow ramp also slows the loop, and a board that lengthens the ramp for an inrush limit has to recheck its transient response afterwards.

Where this order code fits

It is built for notebook VCCIO and DDR VDDQ rails, memory termination supplies and other point-of-load rails that sit behind a 12 V to 20 V adapter and have to keep a battery alive in standby, and the same 800 kHz loop is used in thin clients, panel electronics and portable instrument supplies. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is the 5 V bias separate from the input? Yes. VIN takes 3 V to 22 V and V5 takes 4.6 V to 5.5 V with a 4.4 V typical lockout, so the bias rail has to come up with or before the main input.

Can it be used at -40 C? No. The operating free-air range is -10 C to +85 C, and that is the temperature the assembly has to be qualified to.

Is 10 A available at 85 C ambient? Only with the copper and airflow the 40.2 C/W figure assumes; at 85 C the pad and vias set the real continuous current.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.