Contact Us

ADA4932-2YCPZ-R7

Brand: Analog Devices
Analog Devices ADA4932-2YCPZ-R7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADA4932-2YCPZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

ADA4932-2YCPZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADA4932-2YCPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADA4932-2YCPZ-R7: nine nanoseconds of settling inside a ten nanosecond clock

The ADA4932-2 is a dual low power differential amplifier built on a silicon germanium bipolar process, aimed at the one job that decides the signal to noise ratio of a fast acquisition chain: driving the input of a high performance converter, either single ended to differential or differential to differential. The output common mode is set by an internal feedback loop rather than by external resistors, so the output can be matched to whatever common mode the converter wants while the four resistor network around the part sets the differential gain. The vendor lists it as the next generation of the AD8132 in the same family line.

What the vendor page states

ParameterValue
Functiondual differential amplifier, single ended to differential or differential to differential
Bandwidth560 MHz at a gain of 1, 0.1 dB flat to 300 MHz
Slew rate2800 V per microsecond, 25 to 75 percent
Settling9 ns to 0.1 percent
Input voltage noise3.6 nV per root hertz
Distortion100 dB spurious free dynamic range at 10 MHz, 90 dB at 20 MHz
Input offset0.5 mV typical
Supply current9.6 mA per amplifier
Supply range3 V single supply to plus and minus 5 V
Package and grade24 lead LFCSP, minus 40 to plus 105 C

Two amplifiers, 19.2 mA and 192 mW

Two channels at 9.6 mA each draw 19.2 mA. On a plus and minus 5 V supply that is 192 mW of quiescent dissipation before any signal arrives, and on a single 5 V supply 96 mW. In a 4 by 4 millimetre lead frame package with a pad poured into the ground plane, that is a comfortable rise. In a module that gives the exposed pad a thin trace and calls it a thermal connection, 192 mW is the first thing that shows up as a slow drift in the converter the part is driving, because a bipolar input stage moves its offset with die temperature.

The settling figure is not a sample rate

Nine nanoseconds to 0.1 percent is often read as a 111 MSPS ceiling, and that reading is wrong by a wide margin. A converter running at 100 MSPS does hand the driver a 10 ns period, but the driver only has to be settled when the sampling switch opens, which is a fraction of that period. What 9 ns really tells a buyer is how much of the acquisition window is left for the switch, the trace and the input capacitance of the converter. Put a 9 ns driver in front of a converter whose acquisition window is 3 ns and the numbers do not close, whatever the converter claims.

Noise read against a 16 bit full scale

3.6 nV per root hertz integrated over the 300 MHz the part holds flat is 62.4 microvolts rms, and over the full 560 MHz 85.2 microvolts. On a 2 V peak to peak full scale one 16 bit count is 30.5 microvolts, so this driver alone contributes 2.0 counts over the flat band and 2.8 counts over the whole bandwidth, which is 81.1 dB and 78.4 dB of signal to noise against a full scale tone. That is the ceiling of the chain. A converter behind it that advertises 90 dB will not deliver 90 dB while the front end is wide open, and the only ways out are a band limiting filter before the driver or a lower noise part at lower bandwidth.

The external resistors belong in the error budget

Gain comes from an external four resistor network, and the vendor states that gains below 1 are permitted, which matters when a large intermediate frequency has to be attenuated into a converter's input range rather than amplified. That network's tolerance lands straight on the gain: 0.1 percent resistors give 0.2 percent worst case, 1 percent resistors give 2 percent. A buyer comparing this part against a fixed gain block has to add the cost of four precision resistors, because the amplifier is only half of the gain stage. A 1 V peak to peak signal attenuated to 0.5 V peak to peak is minus 6.02 dB of gain, and the resistor pair that produces it is what sets the accuracy.

Before the order goes out

The single channel version of the same die is the ADA4932-1 in a 16 lead package, so a bill of materials that mixes the two is not a drop in substitution and the pin count has to be checked against the pad on the board first. The amplifier cross reference carries the pin compatible candidates for the older AD8132 that this part replaces, and the converter cross reference lists the converters it is normally paired with. The analog and mixed signal category page holds the rest of the family, including the single channel version.

ADA4932-2YCPZ-R7 noise gain: 560 MHz at unity, 280 MHz at a gain of two, and the four resistors that add 36 uV

The bandwidth figure of 560 MHz belongs to a gain of 1, where there are no feedback resistors. The loop gain that sets the bandwidth is the noise gain, which for a differential amplifier with equal feedback and gain resistors is one plus the ratio, so a gain of 2 has a noise gain of 2 and a bandwidth of about 280 MHz, a gain of 5 gives a noise gain of 5 and 112 MHz, and a gain of 10 gives 56 MHz. A buyer who plans a gain of 10 and budgets 560 MHz has the wrong number by a factor of ten, and the error is in the reading of the specification rather than in the part.

The resistors are part of the noise budget, not outside it

Each feedback and gain resistor contributes thermal noise. At 300 K a 200 ohm resistor is 1.82 nV per root hertz, and four of them in the differential network add in root sum square to 3.64 nV per root hertz. Over a 100 MHz band that is 36.4 uV, which is larger than one code of a 16 bit converter on a 2 V peak to peak span, 30.5 uV. At a gain of 5 with 400 and 100 ohm resistors the sum is 4.07 nV, and at a gain of 10 with 900 and 100 ohm it is 5.76 nV, so the resistor values chosen for gain also set the noise floor. Lower resistor values reduce the noise and load the output more, and the balance is the same one a single ended amplifier faces.

Settling against the clock it has to fit inside

Nine nanoseconds of settling is short, and it is easy to read as a sample rate. It is not. A converter running at 100 MSPS gives 10 ns per sample and a 16 bit pipeline converter may need half of that for its own acquisition, leaving 5 ns for the driver, which this part does not have. The honest use of the figure is against the aperture of the converter: a 10 ns clock with a 9 ns settle leaves 1 ns for everything else, including the track and hold switch and the routing. A 65 MSPS converter with a 15 ns period has room, and that is where this part earns its place.

GainFeedback and gain resistorsNoise gainBandwidthResistor noise over 100 MHz
1none1560 MHznot applicable
2200 and 200 ohm2280 MHz36.4 uV
5400 and 100 ohm5112 MHz40.7 uV
10900 and 100 ohm1056 MHz57.6 uV

Converter driver equivalents are on amplifier cross reference, the converter side of the same chain is on ADC DAC cross reference, and the checks before a substitution are on how to verify a drop in replacement.

Request Quote — In Stock, 100% New & Original, Full Warranty