AD5520JSTZ
Product Specifications
AD5520JSTZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD5520JSTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD5520JSTZ: one pin, four current ranges and a window comparator in a single parametric unit
The AD5520 is a single channel per pin parametric measurement unit, the block that sits at every pin of a semiconductor tester and either forces a voltage while measuring current or forces a current while measuring voltage. It forces and measures over plus or minus 11 V, offers four programmable current ranges of plus or minus 4 microamps, 40 microamps, 400 microamps and 4 milliamps, and accepts an external driver to extend the top of the range to plus or minus 40 milliamps and plus or minus 160 milliamps. Clamp circuitry and window comparators are on the die, which is what turns a source measure loop into a test resource: a comparator that says the pin went outside its window is how an open or a short is caught without waiting for a slow measurement to settle.
What the vendor page states
| Parameter | Value |
|---|---|
| Function | force voltage and measure current, or force current and measure voltage |
| Output voltage range | plus or minus 11 V |
| Force and measure current ranges | plus or minus 4 microamps, 40 microamps, 400 microamps, 4 milliamps |
| Extended ranges | plus or minus 40 milliamps and plus or minus 160 milliamps with an external driver |
| Measured voltage range | plus or minus 11 V |
| On chip | clamp circuitry and window comparators |
| Sensing | force and sense at the tester pin, so cable and relay drop is outside the loop |
| Application | semiconductor automatic test equipment, precision measurement instruments |
Four decades of current, 60 dB inside the part and 92 dB with the driver
The four internal ranges step by a factor of ten, so the span from 4 microamps to 4 milliamps is 1000 to 1, or 60 dB, and adding the external driver stages takes the span to 40,000 to 1, 92 dB, from 4 microamps to 160 milliamps. Each range change moves the resolution by a decade, which means the range decision is a measurement decision and not a convenience. A leakage test on a fresh wafer that runs on the 4 microamp range and then switches to the 4 milliamp range to charge a decoupling capacitor has given up three decades of resolution for the rest of that pin's test.
Forty four milliwatts inside, 1.76 W when the driver takes over
At the internal limit of 4 milliamps into an 11 V compliance the dissipation in the output stage is 44 mW, small enough that a 64 pin tester does not need airflow for it. Move to the extended 160 milliamp range and the same 11 V is 1.76 W per pin, at which point the external driver, its heat sink and the cable resistance are the real subject. That is also where the force and sense pair earns its place: at 160 milliamps, 50 milliohms of relay and cable is 8 mV of drop, and a Kelvin connection to the pin removes it from the measurement instead of correcting for it in software.
What the range and the clamp mean for throughput
The window comparator is the part that shortens a test. Continuity, open and short tests are pass or fail decisions inside a known band, and a comparator that asserts as soon as the pin leaves the band answers in the time of one settling constant instead of one full measured reading. On a device with a few hundred pins, that difference is what sets the parallel test count. The clamps belong in the same argument: a clamp set just outside the expected window protects the pin under test and the unit itself when a part fails short and the loop tries to force a current into it.
Before the order goes out
The AD5520 is a single channel block, so a tester needs one per pin plus a controller per group, and the channel count on the bill of materials is the pin count of the largest device the tester must reach. The ADC and DAC cross reference covers the converters that read these force and measure channels, the component lead time page is the one to open when a parametric unit on an existing platform goes to allocation, and the analog and mixed signal category page holds the rest of the instrumentation blocks.
Request Quote — In Stock, 100% New & Original, Full Warranty