Contact Us

TPS3103E15DBVR

Brand: Texas Instruments
Texas Instruments TPS3103E15DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS3103E15DBVR — Power Management & Signal Chain | Superb Automation

TPS3103E15DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS3103E15DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS3103E15DBVR: 1.5 V supply monitor with a 130 ms reset delay and 1.2 uA of supply current

TPS3103E15DBVR is a supervisor that holds a processor in reset until its rail is valid and pulls it low again whenever the rail sags below the trip point in a SOT-23 (DBV) body of 6 pins. It watches a 1.5 V rail against a 1.434 V threshold at 25 degrees, draws 1.2 uA typical, delays the release of reset by 65 to 195 ms after the rail passes the threshold, and brings out a manual reset pin plus a second comparator input for a power fail or sense signal. Reset is defined with the supply as low as 0.4 V.

Order code and package

Ordering stringTPS3103E15DBVR, the six pin SOT-23 body on a 3000 piece large reel
Part markingPFXI on the body, with the 250 piece reel carrying the same marking
BodySix pin SOT-23, 3.23 mm by 3.17 mm including the leads
MaterialRoHS compliant, nickel palladium gold finish, moisture level 1 with unlimited floor life at 260 degrees
Suffix decodingE15 is the 1.5 V supervision version, and the E, H and K codes in this family select 0.9 V, 1.2 V, 1.6 V, 2.0 V and 3.3 V variants
Reel sizes3000 pieces on the large reel for the R suffix, 250 on the small reel for the T suffix, and a G4 row of the same string at both sizes
FamilyTPS3103 and TPS3106 are open drain reset with a power fail or sense input, while TPS3110 is push pull reset with a watchdog for a processor that has to be checked while it runs

Electrical parameters that decide the application

Threshold1.434 V typical at 25 degrees for the E15 version, rising to a 1.505 V maximum over the full temperature range, which is the number a rail tolerance has to be checked against
Trip accuracy0.75 per cent on the threshold, and a temperature coefficient of minus 0.019 per cent per degree, so the trip point drifts down as the board warms
Supply current1.2 uA typical, which is low enough to stay on a battery rail that the processor leaves powered
Reset delay65 to 195 ms with 130 ms typical, generated inside the part rather than set by an external capacitor
Manual resetThe MR pin has an internal pull up of 70 to 130 kOhm, so it can be left open or driven from a test point, a push button or a debug header
Propagation40 us from the supervised supply crossing the threshold to the reset output changing, and 1 to 5 us from the manual reset pin
OutputOpen drain, active low, rated to 5.5 V and able to sink current from a pull up on a different rail than the one being watched
Second inputA power fail or sense comparator with its own output, used to watch a second rail or to flag a decaying input before the main rail drops
Reset validityThe reset output is defined and low with the supply anywhere from 0.4 V up, so the processor is held through the whole ramp rather than only after the part wakes
HysteresisBuilt into the comparator, which keeps a rail that sits near the threshold from chattering the reset line
Temperatureminus 40 to 125 degrees, and the trip window is specified over that range rather than only at room temperature
Hysteresis at the sense inputSeparately specified for the second comparator, so a power fail warning on a divided rail does not need an external filter to be stable

Family variants and how they differ

TPS3103 against TPS3106Both are open drain reset with a second comparator input. The difference is whether that input is a power fail input with its own output or a sense input compared against the same reference, which decides how a second rail is watched
TPS3110Push pull reset and a watchdog timer. A watchdog is what a supervisor needs when the failure of interest is a processor that hangs rather than a rail that sags, and this member of the family is the one that covers it
Fixed thresholdsThe threshold is set by an internal divider and cannot be changed. A rail that needs a different trip point needs a different suffix, not an external resistor network
Open drain outputTwo supervisors can share one reset line, and the line can be pulled to a rail other than the one being supervised. That is why this output type is used on boards where a 3.3 V processor is reset by a 1.5 V rail monitor
No external delay capacitorThe 130 ms delay is internal and fixed, which removes a part but also removes the option of stretching the delay for a processor with a slow oscillator start
Custom thresholdsThe vendor offers custom trip points on the same die with a minimum order quantity, which is the route for a rail whose tolerance does not fit any listed suffix

Points to check before this part goes on a BOM

A 1.5 V rail with a five per cent tolerance sits at 1.425 V at its low limit, which is inside the 1.434 V typical trip point. A board built that way will assert reset on a rail that is still within its own specification, so the regulator tolerance and the trip window have to be looked at together.

The trip point drifts down with temperature at about 0.019 per cent per degree. Over a 100 degree rise that is roughly 27 mV, which is larger than the difference between the typical and the maximum threshold on some rails.

The reset delay is fixed at 130 ms typical. A processor whose oscillator takes longer than that to stabilise will come out of reset before its clock is valid, and the fix is a different part or a second enable, not a capacitor.

The open drain output needs a pull up, and the pull up can sit on a different rail from the one being supervised. That is a feature, but it also means the reset line is only low when that pull up rail is present, which matters on a board with several supplies.

Supply current of 1.2 uA is the reason this part stays on a battery rail permanently. A supervisor that draws 50 uA would flatten a coin cell in months, and the threshold accuracy of this part is the trade for that current.

The manual reset pin has an internal pull up in the tens of kiloohm. Leaving it floating is acceptable, but a long trace to a front panel button picks up noise, and the 1 to 5 us response means the part will follow that noise onto the reset line.

What a supervisor actually protects against

A processor that loses its supply slowly is the dangerous case. The rail falls, the oscillator keeps running for a while, and the core executes from an address it has fetched from a supply that is no longer valid. The result is not a clean shutdown but an undefined state that may write to non volatile memory or drive an output that controls a relay.

A supervisor makes that case defined. It asserts reset while the rail is below the threshold and holds it for a fixed delay after the rail is valid again, so the processor starts from a known state. The 1.2 uA supply current is what allows that function to stay powered on a battery rail that is otherwise off.

Where this order code fits

Battery powered instruments, wireless sensor nodes, portable medical monitors and any board built around a low power microcontroller or DSP where the rail that has to be supervised is the same rail that powers the processor. In those boards the supervisor cannot draw more current than the processor in its sleep state, which is why the 1.2 uA figure rather than the threshold accuracy tends to decide the part. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Does the reset delay need an external capacitor? No. The delay is generated inside the part and is 130 ms typical, between 65 and 195 ms over the specified range, so there is no external timing component to select or tolerate.

Can two supervisors drive the same reset line? Yes, because the output is open drain. Both can pull the line low and either can release it, which is how a board with a main rail and an auxiliary rail avoids two separate reset nets.

What is the second input for? On this family it is either a power fail input or a sense input, used to watch a second rail or to give early warning that the input is decaying before the main rail crosses its threshold.

Is there a watchdog version? Yes, the TPS3110 in the same family has push pull reset and a watchdog timer, for a processor that has to be checked while it runs rather than only while its rail comes up.

How low can the supply go while reset is still valid? The output is defined and low with the supply at 0.4 V, which covers the whole ramp of a 1.5 V rail rather than only the part of it above the threshold.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Date Code Management page sets out the checks that keep a substitute from failing on the bench.