Contact Us

INA121UA

Brand: Texas Instruments
Texas Instruments INA121UA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA121UA — Power Management & Signal Chain | Superb Automation

INA121UA

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA121UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA121UA: the A grade of the FET input amplifier in an SO-8 tube

The INA121UA combines the two choices that a small instrument build usually makes at once: the surface mount body rather than the DIP, and the tighter of the two offset bins rather than the plain one. It is the same die as the rest of the family, in the eight pin SO-8 body, supplied in a 75 piece tube. The A suffix is a laser trimmed bin, so the part is not a different circuit; it is a part that passed a tighter test.

For a channel that will be calibrated once and then sealed, the grade buys margin rather than accuracy. The calibration removes the room temperature offset either way, and what remains is the drift, which is the family row and does not change with the grade. The margin the grade buys is the headroom between the untrimmed offset and the point at which the trim network runs out of range, which on a 200 µV part with a 10 mV full scale is a real constraint on the trim resistor values.

The INA121UA rows as the addendum publishes them

Part classFET input instrumentation amplifier, current feedback
Vendor statusACTIVE, production data
Data sheetSBOS078
GradeA suffix, tighter laser trimmed offset bin
Gain equationG = 1 + 50 kΩ divided by RG
Gain range1 to 10,000 V/V
Input offset voltagePlus or minus 200 µV, family row
Offset driftPlus or minus 2 µV per degree
Input bias currentPlus or minus 4 pA
Common mode rejection106 dB
Quiescent current450 µA
Supply rangePlus or minus 2.25 V to plus or minus 18 V
BodySOIC, D outline, 8 pins
Carrier75 pieces per tube
Reel siblingINA121UA/2K5, 2500 pieces
Plain grade siblingINA121U, same body same tube
Moisture levelLevel 3, 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees

The tube of 75 is a convenient quantity for a build of a few hundred channels, and it is also the carrier with the worst moisture behaviour, because a tube is opened and resealed far more often than a reel. Each opening starts the 168 hour clock again only if the parts are returned to dry storage; a tube left on a bench overnight in a humid month is a tube that needs a bake, and the bake is 24 hours at 125 degrees that nobody planned for.

Two grades in one tube family and a receiving trap

The plain and the A grade look identical. The marking differs and the tube label differs, and a distributor picking from a bin that contains both can ship either. A receiving inspection that reads the label against the purchase order catches this in a minute; an inspection that counts tubes and files them catches it at final test, three weeks later, with 200 boards to rework. The cost of the check is trivial and the cost of skipping it is not.

The second trap is the slash. The reel sibling is printed by the vendor as INA121UA/2K5, and a catalogue that strips the slash produces a string that a distributor's search may not match. The catalogue on this site records both forms, and a purchase order that copies the string without the slash is still the same part, but an automated system that matches on exact strings will fail to find it.

A picoamp input on a reflowed board

A surface mount assembly is cleaned less often than a through hole one, because the flux is no clean and the cleaning step was removed from the process years ago. That is a problem for a 4 pA input: no clean flux residue on a board that sees humidity is a leakage path, and the leakage path is in parallel with the source. A board with a high impedance front end should either be cleaned or be laid out so that the residue cannot bridge the input traces, and the second option is a keep out around the input pins rather than a process change.

The guard ring is the other measure, and on SO-8 it is easier than on a DIP because the pins are closer and the ring can be drawn tightly around them. The ring is driven from the reference node, which on a bipolar supply is ground; on a single supply it is the mid rail, and a ring driven from a mid rail that is not buffered will inject the divider noise into the input. The ring has to be a low impedance node, which is why ground is the usual choice.

What 106 dB of rejection actually rejects

Common mode rejection is specified at DC and falls with frequency, and the number that matters on a real channel is the rejection at the frequency of the interference rather than at zero. A mains frequency common mode signal on a long cable is the usual disturbance, and the rejection at 50 or 60 Hz is close to the DC figure; a switching supply at 200 kHz is a different problem, and the rejection there is limited by the capacitance mismatch between the two input paths rather than by the amplifier. Matched input capacitors are the way to hold the rejection at high frequency, and the data sheet recommends a differential capacitor that is much larger than the common mode ones.

The 106 dB is also a minimum, not a typical. A part that measures 106 dB on the bench is at the edge of the specification, and a channel that needs 110 dB has to be selected or has to use a different topology. The distinction is worth making in a requirement document, because a minimum and a typical are not the same guarantee.

Where this grade and body combination fits

A multi channel data acquisition card is the natural home: several of these in a row, reflowed in one pass, each with its own gain resistor and its own input protection, feeding a multiplexer. The A grade keeps the trim network simple, the SO-8 body keeps the process simple, and the tube of 75 matches a build of 20 to 30 cards. A single channel instrument would take the same part, but the process argument for the SO-8 is weaker there because there is only one part to place.

A battery powered instrument is the other case. At 450 µA the part runs for months from a modest cell, and the SO-8 body has no socket to corrode in a humid enclosure. The picoamp input is what the instrument needs if the sensor is a pH electrode or a photodiode in photovoltaic mode, and the 40 V protection is what it needs if the sensor is on a cable that a user can unplug while the instrument is on.

Buying INA121UA

The tube is active and the reel is active. For a build under about 150 pieces the tube is the right carrier; above that the reel is cheaper per piece and the moisture management is simpler because a reel is opened less often. The grade should be named on the order because the plain part in the same body is a different offset bin and the two are visually identical.

For a programme that expects to run for years, the question is not whether the part is available today but what happens when the DIP sibling disappears, because the tube market for DIP parts is shrinking. Our component obsolescence management page sets out how we watch for that, and the pin to pin cross reference page lists the parts we can compare when a family narrows.

Questions that arrive with this part number

Whether the A grade can be substituted by the plain grade is the first question, and technically yes with a wider offset at the same drift. Whether the tube can be replaced by the reel mid programme is the second, and it can, because the body and the die are identical; only the carrier and the moisture handling change. The third question is the finish, which the addendum publishes as call TI, so the first article should be inspected rather than assumed.

The fourth is about cleaning. A board with this part on a no clean process is not automatically a leakage problem, but a board that has been hand touched around the input pins is. The handling rule is gloves, and the board rule is a keep out, and both are cheaper than a field return.