INA111AU
Product Specifications
INA111AU
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA111AU from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA111AU: the same FET input amplifier in a 16 pin SOIC
The INA111AU is the surface mount member of the INA111 family, in the 16 pin wide body SOIC that the vendor calls DW. The die is the same high speed FET input instrumentation amplifier as the plastic DIP member: current feedback topology, 2 MHz at a gain of 10, 4 microseconds settling to 0.01 per cent at a gain of 100, and 20 pA maximum input bias current. A single resistor sets any gain from 1 to over 1000, and common mode rejection is 106 dB minimum at a gain of 100.
The package is the reason a buyer asks for this suffix. Sixteen pins in a 10.3 by 10.3 millimetre body give the same function as the eight pin DIP at a quarter of the height, and the four extra pins are no connects on this device, which is worth knowing before a board is routed to them. A tube of 40 pieces is the standard carrier, and the same body ships 1000 pieces on a reel under the slash one K string.
The INA111AU rows as the addendum publishes them
| Part class | FET input instrumentation amplifier, current feedback |
| Vendor status | ACTIVE, production data |
| Data sheet | SBOS015, March 1998 |
| Gain equation | G = 1 + 50 kΩ divided by RG |
| Gain range | 1 to over 1000 V/V |
| Input bias current | 20 pA maximum |
| Offset drift | 5 µV per degree maximum |
| Common mode rejection at G = 100 | 106 dB minimum |
| Bandwidth at G = 10 | 2 MHz |
| Bandwidth at G = 100 | 450 kHz |
| Settling to 0.01 per cent | 4 µs at G = 100 |
| Quiescent current | 3.3 mA typical, 4.5 mA maximum |
| Supply range | 6 V to 18 V |
| Output swing | 11 V minimum at 5 mA into 2 kΩ |
| Capacitive load stability | 1000 pF |
| Body | SOIC, DW outline, 16 pins, 10.3 by 10.3 millimetres |
| Carrier, tube row | 40 pieces in a tube |
| Carrier, reel row | 1000 pieces on a large tape and reel under the slash one K string |
| Lead finish | Nickel palladium gold |
| Moisture level, tube row | Not applicable to this package type |
| Moisture level, reel row | Level 3 at 260 degrees, 168 hour floor life |
| Temperature range | Minus 40 to plus 85 degrees |
| Part marking | INA111AU |
Note how the moisture level changes between the two rows of the same part. The tube row carries no floor life because the parts are not on tape, while the reel row is level 3 with a 168 hour window once the reel is opened. A build that pulls a partial reel for a short run and puts it back on the shelf starts that clock again only if the parts go into a dry pack, and a level 3 part left out for a week needs a bake before the next reflow.
Sixteen pins, four of them not connected
The DW body is a 16 pin outline borrowed from the dual amplifier footprint of the same era, and this device uses 8 of the 16 pins. The four no connects sit between the functional pins, which is helpful for creepage on a board with a high voltage common mode but harmful if a board is routed to them expecting a second channel. The pin out does not match the eight pin DIP pin for pin, so a board that is converted from through hole to surface mount needs the full pin map rather than a mechanical translation.
The extra spacing has one real benefit on a mixed signal board. The input pins are further apart, so the leakage path between them is longer, and on a part specified at 20 pA of bias current that distance is worth more than it looks. A 10 GΩ leakage path between two adjacent pins is 10 pA at 100 mV of differential, which is half the bias current specification gone before the board is even powered.
Reel, tube and the floor life arithmetic
The reel string is 1000 pieces and the tube is 40, a ratio of 25 to 1, so the choice is really about the size of the build. A run of 200 boards with one part each is five tubes or a fifth of a reel, and a partial reel is the worst of both worlds because it carries the floor life clock without the convenience of a sealed pack. The tube has no floor life at all, which makes it the better carrier for a low volume build even though the unit handling cost is higher.
For a build above a few hundred boards a year, the reel is the right answer and the moisture controls should be in place before the first reel is opened, not after the first bake is needed. A dry cabinet at 10 per cent relative humidity removes the clock entirely, and it costs less than the schedule slip from a rejected reel.
Supply decoupling on a wide body
The 3.3 mA of quiescent current is small enough that a single 100 nF capacitor per rail close to the pin is adequate, and the 4.5 mA maximum leaves room for a 10 µF bulk part shared with the rest of the card. What the decoupling has to handle is not the quiescent current but the transient in the output stage: a 10 V step into 2 kΩ is 5 mA of load current that appears in a microsecond, and a supply trace with 100 nH of inductance will move the rail by 500 mV if the capacitor is at the other end of the board.
A ground plane under the part is worth the layer. The reference pin carries the return for the input stage, and a 10 mΩ of shared ground impedance against a 20 pA bias current is nothing, but the same impedance against the 5 mA output current is 50 µV, which is a real error on a 10 mV signal. The reference should be returned to the converter reference, not to the nearest ground via.
Buying INA111AU
The tube string is active with 40 pieces per tube, and the slash one K string is the 1000 piece reel. The two carry the same die and the same marking, so a purchase order can switch carriers without a qualification, but the receiving inspection differs: a reel has a label with a quantity and a date code that a line can scan, a tube has a label and a lot number that has to be read by hand.
The A grade is the looser offset bin of the family, and the B grade in the same body costs a little more for a tighter offset. On a board that is trimmed at test the A grade is sufficient, and on a board that is not, the B grade is the cheaper way to reach a 1 per cent accuracy target without adding a calibration step.
Questions that arrive with this part number
Whether the AU can be soldered with a lead free process is the first question. It can: the finish is nickel palladium gold, the reel row is rated to 260 degrees, and the body is compatible with a standard reflow profile. The tube row carries no moisture level, which is not a statement that the parts are dry, only that the vendor does not assign a floor life to that carrier.
The second question is whether the 16 pin body can replace an eight pin part on an existing board. It cannot without a board change, because the pin out differs, and a customer who assumes a mechanical adapter will work usually finds the feedback pin in the wrong place.
For a customer moving this part from tube to reel, our amplifier cross reference page lists the carriers we can confirm against the vendor addendum, and the date code page explains how a partial reel is checked before it is issued to a line.