Contact Us

INA121UA2K5

Brand: Texas Instruments
Texas Instruments INA121UA2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA121UA2K5 — Power Management & Signal Chain | Superb Automation

INA121UA2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA121UA2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA121UA/2K5: the A grade on a 2500 piece reel

This is the production quantity of the A grade in the SO-8 body: 2500 pieces on a large reel, the same die and the same electrical rows as the tube part, with the tighter offset bin and the carrier that a placement line wants. The slash in the vendor string is part of the orderable number and the catalogue records the string both ways, which matters when a purchase order is generated from a catalogue rather than typed by hand.

The reasons to choose this row over the tube row are all logistic: one carrier per line, one label per reel, one moisture exposure per build rather than one per tube. On a build of a thousand boards the difference in handling time is measured in hours, and on a build of a hundred it is not worth opening a reel at all.

The INA121UA/2K5 rows as the addendum publishes them

Part classFET input instrumentation amplifier, current feedback
Vendor statusACTIVE, production data
Data sheetSBOS078
GradeA suffix, tighter offset bin
Catalogue stringINA121UA/2K5, stored here also as INA121UA2K5
Gain equationG = 1 + 50 kΩ divided by RG
Input offset voltagePlus or minus 200 µV
Offset driftPlus or minus 2 µV per degree
Input bias currentPlus or minus 4 pA
Common mode rejection106 dB
Quiescent current450 µA
BodySOIC, D outline, 8 pins
Carrier2500 pieces on a large reel
Tube siblingINA121UA, 75 pieces per tube
Plain grade reelINA121U/2K5, same reel different bin
Moisture levelLevel 3, 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees

A reel of this size at level 3 is a two person problem: one to move it and one to record the opening. The record matters because the floor life is cumulative and a programme that opens the same reel every month needs to know when the total exposure has run out. A simple log on the reel label, with the date and the hours out of dry storage, is what an auditor asks for and what the assembly house rarely keeps.

The reel, the feeder and the orientation

SO-8 tape is 12 mm wide with a 4 mm pitch, and the reel fits the standard feeder on any line. The orientation is set by the quadrant the parts are taped in, and it is the vendor's, not the distributor's. A reel that has been decanted, tested and re-taped by somebody else is a reel whose orientation is somebody else's decision, and a reversed reel places every part rotated by 180 degrees, which on an eight pin part is a dead channel rather than an obvious fault.

The first article check should therefore verify the orientation visually before any board is populated at volume, and it should verify it on the reel that will be used, not on the sample that arrived in a tube. This is a small discipline that saves a batch, and it is the same discipline on every reel of every part, so the marginal cost once the procedure exists is near zero.

Gain setting on a production board

A production build uses one gain per board, and the gain resistor is placed once. The tolerance of that resistor is the dominant gain error, and a 0.1 per cent part with a low temperature coefficient is the cheap answer. The alternative is to trim the gain at test, which needs a potentiometer or a selected resistor and a test step, and a test step costs more than the resistor unless the volume is very high.

The gain also sets the bandwidth, and a production board that has to measure a step should be checked for settling at the actual gain rather than at unity. A part that looks fast in a sine sweep can still show a 20 microsecond tail on a step at a gain of 100, and on a multiplexed input that tail is crosstalk between channels. The vendor curve is the reference, and the first article is the proof.

Where the reel quantity pays for itself

The break even between a reel and a tube is roughly at the point where the number of tubes opened exceeds the number of reels that would have been opened, because the handling cost is per opening rather than per piece. In practice that is a few hundred pieces per build for an eight pin part. Below that, a tube per build is simpler; above it, a reel per quarter is simpler and the moisture log is one line per quarter rather than one per tube.

The reel also changes the failure mode of a shortage. With tubes, a missing tube is a missing hundred boards and can be covered from another tube; with a reel, a short reel is discovered at the end of a build, when there is no time to reorder. Counting the reel at receiving and recording the count against the label is the control, and it takes less time than the shortage it prevents.

Buying INA121UA/2K5

The reel is active, and the grade is the A bin. The purchase order should name the grade, the carrier and the quantity in pieces rather than in reels, because a distributor quoting two reels of 2500 against a requirement of 3000 pieces has made a rounding decision on the customer's behalf. The slash in the string should be kept if the customer's system accepts it, and the stripped form is acceptable everywhere else.

For a long programme, the buffer question is the same as for any active part with a narrow market: hold enough to cover the requalification time of a substitute, not enough to cover a price move. Our last time buy and lifetime buy page sets out the arithmetic, and the date code management page covers the rotation that keeps a reel from ageing in the stores.

Matching channels when the parts share a reel

A board with two of these amplifiers has two independent offsets, and the difference between them is a differential error that no single trim removes. Parts from one reel share a lot and a trim history, which makes the difference smaller than the data sheet limits suggest, but it does not make it zero. A production build that needs a matched pair should either select on measurement or bring both channels from the same reel and accept the residual.

There is a cheaper trick for a differential channel: place the two amplifiers so that they see the same thermal gradient, and trim the pair rather than each part. A gradient across 20 mm of board at 5 degrees is 10 µV of differential drift at 2 µV per degree, which on a 1 mV full scale is 1 per cent. Mechanical symmetry is free and is worth more than a tighter grade on a two channel board.

Questions that arrive with this part number

Whether the reel can be split is the first question, and it can, by a distributor with taping equipment, but the split is no longer the vendor's carrier and the moisture history restarts. Whether the part is available in a smaller reel is the second, and the vendor's rows for this body are the tube and the 2500 piece reel, so a smaller quantity comes from a tube or from a distributor split. The third question is price: a reel is cheaper per piece, and the saving is usually larger than the carrying cost at any reasonable build rate.

The fourth question is whether the same die and grade exist in the DIP body for prototyping, and they do, as INA121PA, which lets a prototype be built with the same electrical part before the board is committed to reflow.